| Manufacturer | VDF |
|---|---|
| Model | 450-T4/2000 |
| Year | 2012 |
| Location | Germany
|
This listing features a VDF 450-T4/2000 CNC turning center, manufactured in 2012, designed for automated production of axles, shafts, and similar cylindrical components. The machine offers a maximum swing diameter over the bed of 700 mm and a turning diameter up to 650 mm, with a maximum workpiece length of 2200 mm. It has a robust build with overall dimensions of 5100 mm in length, 2800 mm in width, and 2860 mm in height, weighing approximately 27,000 kg.
Equipped with two Sauter BA-977 disk-type servo turrets, each featuring 12 tool positions capable of holding driven/live tools with VDI 50 taper, the machine supports high-precision simultaneous or sequential multi-operation machining. Both turrets have X-axis travel of 340 mm and Z-axis travel of 2460 mm, with the right turret also offering a Y-axis travel of +/- 100 mm for off-center machining. The spindle features a bore diameter of 103 mm and a maximum speed of 2800 rpm, powered by a 60 kW motor delivering up to 5335 Nm of torque at 60% duty cycle. The machine includes a C-axis with 0.001-degree resolution and a maximum speed of 30 rpm.
The lathe is fitted with a Rohm 320/3 hydraulic combination 3-jaw chuck with retractable jaws and a powered face driver, allowing full-length roughing and finishing in a single setup. It also includes a Rohm hydraulic steady rest with a clamp range of 50 to 315 mm, and a servo-controlled programmable tailstock with MT#5 taper and 18 kN force.
Additional features include a mineral concrete machine base for vibration resistance, high-speed rapid movements (up to 30,000 mm/min on Z-axis), a comprehensive chip conveyor system with a capacity of 400 kg/h, and advanced coolant and filtration systems. The CNC control is a Siemens Sinumerik 840Dsl Solution Line with Ethernet and USB connectivity.
Visual inspection shows the machine exterior is clean and well-maintained, with closed safety doors and a control panel on the right side featuring an intact display and buttons. The working area is clean and intact, with two chucks and a protective curtain visible. The tailstock and tool holders show some signs of wear and minor paint chipping but no structural damage. Electrical and hydraulic components, including control boxes and cables, are present with some surface dirt but no visible damage.
This machine comes complete with static tool holders, a Marposs T18 toolsetting probe with electrical interface, a central lubrication unit, oil-mist filtration and suction system, and comprehensive documentation covering operation, programming, maintenance, and spare parts.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
Swing diameter over the bed: 700 mm
Turning diameter: max. 650 mm
Workpiece length: max. 2200 mm
Travels:
Upper Tool Turret Left:
Facing travel: X 340
Longitudinal travel : Z 2460 mm
Upper Tool Turret Right:
Facing travel: X 340 mm
Vertical travel for off centre machining: Y +/- 100 mm
Longitudinal travel: Z 2460 mm
Rapids: X/X2/Y 15000 mm/min.
Z/Z2/W1/W2 30000 mm/min.
Spindle nose: DIN 55026
Spindle bore: 103 mm
Spindle bearing diameter: 150 mm
Spindle drive motor rating: 100% / 60% 60 / 72 KW
Spindle speeds: 0 - 2800 rpm
Gear steps: 2
Spindle torque: 100% / 60% 4444 / 5335 Nm
C-Axis: C 0.001 degrees
C-Axis speeds: 0 - 30 rpm
C-Axis torque max.: 40% 600 Nm
Chuck diameter: 320 mm
Chuck type: Roehm 320/3
Tool Turrets: 2 x Sauter Disc-Type (Servo)
Upper Tool Turret Left - Turret tool positions: 12
Driven/Live tool positions: max. 12
Tool taper: VDI 50
Driven/Live tool motor rating: 100% 8.17 KW
Driven/Live tool speeds: rpm
Drive torque: 100% 48 Nm.
Upper Tool Turret Right - Turret tool positions: 12
Driven/Live tool positions: max. 12
Tool taper: VDI 50
Driven/Live tool motor rating: 100% 8.17 KW
Driven/Live tool speeds:
Drive torque: 100% 48 Nm.
Tailstock taper: MT#5
Tailstock force: 18 kN
Hydraulic steady rest:
Steady rest clamp range: 50 - 315 mm
Chip conveyor:
Chip volume output: 400 kg/h
Discharge height: 1300 mm
Electrics: 400-480 V / 3 Ph / 50-60 Hz.
Machine weight: 27000 kg
Length x Width: 5100 x 2800 mm
Height: 2860 mm
Equipped with: VDF 450-T4/2000 8-Axis CNC Turning Center for Automated Production of Axles, Shafts, or similar cylindrical products.
CNC Control: Siemens Sinumerik 840Dsl Solution Line; Ethernet; Front Port USB.
Machine Features:
Twin Upper Left and Right Sauter BA-977 Disk-type Power Servo Turrets permitting highly accurate simultaneous or 1st /2nd/3rd op single setup cutting on workpieces; C-axis in main spindle;
Driven-tool capability in both upper turrets;
Y-axis in Upper Right turret;
Rohm 320/3 KKHFR Hydraulic Combination 3-Jaw Chuck featuring (counter) centrifugal-force compensation, powered face-driving center, and retractable clamping jaws at speeds below 500 rpm to permit full length roughing and finish-turning of shaft in single setup; Rohm Hydraulic turn-through steady rest Model SLZ.50315/C100- Servo-controlled and air purge for programmable positioning including interference-free locations behind main spindle and tailstock;
Servo-controlled programmable tailstock with independent cooling and pressure monitoring;
Geared High power AC Spindle motor (72 kWP @ 60% duty cycle, achieved at 130 RPM)/ produces 5335 Nm torque at spindle at 60% DC - sustainable to 130 RPM;
MINERALIT polymer concrete machine base for vibration resistance.
Equipped with:
-Rohm 320/3 Hydraulic 3-Jaw Combination Clamping and Face Driving Chuck with retractable clamping arms/jaws, and power-operated face driver. (Retract jaws to machine jaw clamping seat- part is driven by powered face driver; return jaws to clamp on part for rough turning; retract jaws again to finish turn full length end to end, driven by face driver).
-Rohm SLZ.50315/C100 Hydraulic Steady Rest 50-315 mm clamping range
- 2x (Left/Right) 12-Station Sauter Servo Power Disk Turrets (for static or driven rotary tools)
-Assortment of static tool holders
-Marposs T18 Toolsetting Probe with E32R Electrical Interface and Auto Arm
-Central lubrication unit
-Oil-Mist Filtration and Suction System
-Brinkmann/Knoll High-pressure coolant system including pumps, filtration, and reservoir
-Knoll Chip Filtration and Conveyor System
-Comprehensive documentation for machine operation, controls, programming, job setup, maintenance, assembly drawings, sub-assembly drawings & maintenance; spare parts lists, etc, in printed and electronic forms
Condition: Excellent
Please note that this description may have been translated or optimized with artificial intelligence (AI) automatically. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase.
What type of products can this Boehringer VDF 450-T4/2000 CNC lathe produce?
This Boehringer VDF 450-T4/2000 CNC lathe is an 8-axis turning center designed for automated production of axles, shafts, or similar cylindrical products.
How long has this VDF 450-T4/2000 CNC lathe been available?
This VDF 450-T4/2000 CNC lathe has been on the market for two years.
Is this CNC lathe open to serious offers?
This CNC lathe is available for serious offers.
When was this VDF 450-T4/2000 CNC lathe manufactured?
This VDF 450-T4/2000 CNC lathe was manufactured in 2012.
The following questions and answers are generated using artificial intelligence based on the product information available. They are provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
| Client type | Machinery dealer |
| Active since | 2004 |
| Offers online | 40 |
| Last activity | Nov. 4, 2026 |
Swing diameter over the bed: 700 mm
Turning diameter: max. 650 mm
Workpiece length: max. 2200 mm
Travels:
Upper Tool Turret Left:
Facing travel: X 340
Longitudinal travel : Z 2460 mm
Upper Tool Turret Right:
Facing travel: X 340 mm
Vertical travel for off centre machining: Y +/- 100 mm
Longitudinal travel: Z 2460 mm
Rapids: X/X2/Y 15000 mm/min.
Z/Z2/W1/W2 30000 mm/min.
Spindle nose: DIN 55026
Spindle bore: 103 mm
Spindle bearing diameter: 150 mm
Spindle drive motor rating: 100% / 60% 60 / 72 KW
Spindle speeds: 0 - 2800 rpm
Gear steps: 2
Spindle torque: 100% / 60% 4444 / 5335 Nm
C-Axis: C 0.001 degrees
C-Axis speeds: 0 - 30 rpm
C-Axis torque max.: 40% 600 Nm
Chuck diameter: 320 mm
Chuck type: Roehm 320/3
Tool Turrets: 2 x Sauter Disc-Type (Servo)
Upper Tool Turret Left - Turret tool positions: 12
Driven/Live tool positions: max. 12
Tool taper: VDI 50
Driven/Live tool motor rating: 100% 8.17 KW
Driven/Live tool speeds: rpm
Drive torque: 100% 48 Nm.
Upper Tool Turret Right - Turret tool positions: 12
Driven/Live tool positions: max. 12
Tool taper: VDI 50
Driven/Live tool motor rating: 100% 8.17 KW
Driven/Live tool speeds:
Drive torque: 100% 48 Nm.
Tailstock taper: MT#5
Tailstock force: 18 kN
Hydraulic steady rest:
Steady rest clamp range: 50 - 315 mm
Chip conveyor:
Chip volume output: 400 kg/h
Discharge height: 1300 mm
Electrics: 400-480 V / 3 Ph / 50-60 Hz.
Machine weight: 27000 kg
Length x Width: 5100 x 2800 mm
Height: 2860 mm
Equipped with: VDF 450-T4/2000 8-Axis CNC Turning Center for Automated Production of Axles, Shafts, or similar cylindrical products.
CNC Control: Siemens Sinumerik 840Dsl Solution Line; Ethernet; Front Port USB.
Machine Features:
Twin Upper Left and Right Sauter BA-977 Disk-type Power Servo Turrets permitting highly accurate simultaneous or 1st /2nd/3rd op single setup cutting on workpieces; C-axis in main spindle;
Driven-tool capability in both upper turrets;
Y-axis in Upper Right turret;
Rohm 320/3 KKHFR Hydraulic Combination 3-Jaw Chuck featuring (counter) centrifugal-force compensation, powered face-driving center, and retractable clamping jaws at speeds below 500 rpm to permit full length roughing and finish-turning of shaft in single setup; Rohm Hydraulic turn-through steady rest Model SLZ.50315/C100- Servo-controlled and air purge for programmable positioning including interference-free locations behind main spindle and tailstock;
Servo-controlled programmable tailstock with independent cooling and pressure monitoring;
Geared High power AC Spindle motor (72 kWP @ 60% duty cycle, achieved at 130 RPM)/ produces 5335 Nm torque at spindle at 60% DC - sustainable to 130 RPM;
MINERALIT polymer concrete machine base for vibration resistance.
Equipped with:
-Rohm 320/3 Hydraulic 3-Jaw Combination Clamping and Face Driving Chuck with retractable clamping arms/jaws, and power-operated face driver. (Retract jaws to machine jaw clamping seat- part is driven by powered face driver; return jaws to clamp on part for rough turning; retract jaws again to finish turn full length end to end, driven by face driver).
-Rohm SLZ.50315/C100 Hydraulic Steady Rest 50-315 mm clamping range
- 2x (Left/Right) 12-Station Sauter Servo Power Disk Turrets (for static or driven rotary tools)
-Assortment of static tool holders
-Marposs T18 Toolsetting Probe with E32R Electrical Interface and Auto Arm
-Central lubrication unit
-Oil-Mist Filtration and Suction System
-Brinkmann/Knoll High-pressure coolant system including pumps, filtration, and reservoir
-Knoll Chip Filtration and Conveyor System
-Comprehensive documentation for machine operation, controls, programming, job setup, maintenance, assembly drawings, sub-assembly drawings & maintenance; spare parts lists, etc, in printed and electronic forms
Condition: Excellent
Please note that this description may have been translated or optimized with artificial intelligence (AI) automatically. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase.
What type of products can this Boehringer VDF 450-T4/2000 CNC lathe produce?
This Boehringer VDF 450-T4/2000 CNC lathe is an 8-axis turning center designed for automated production of axles, shafts, or similar cylindrical products.
How long has this VDF 450-T4/2000 CNC lathe been available?
This VDF 450-T4/2000 CNC lathe has been on the market for two years.
Is this CNC lathe open to serious offers?
This CNC lathe is available for serious offers.
When was this VDF 450-T4/2000 CNC lathe manufactured?
This VDF 450-T4/2000 CNC lathe was manufactured in 2012.
The following questions and answers are generated using artificial intelligence based on the product information available. They are provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
This listing features a VDF 450-T4/2000 CNC turning center, manufactured in 2012, designed for automated production of axles, shafts, and similar cylindrical components. The machine offers a maximum swing diameter over the bed of 700 mm and a turning diameter up to 650 mm, with a maximum workpiece length of 2200 mm. It has a robust build with overall dimensions of 5100 mm in length, 2800 mm in width, and 2860 mm in height, weighing approximately 27,000 kg.
Equipped with two Sauter BA-977 disk-type servo turrets, each featuring 12 tool positions capable of holding driven/live tools with VDI 50 taper, the machine supports high-precision simultaneous or sequential multi-operation machining. Both turrets have X-axis travel of 340 mm and Z-axis travel of 2460 mm, with the right turret also offering a Y-axis travel of +/- 100 mm for off-center machining. The spindle features a bore diameter of 103 mm and a maximum speed of 2800 rpm, powered by a 60 kW motor delivering up to 5335 Nm of torque at 60% duty cycle. The machine includes a C-axis with 0.001-degree resolution and a maximum speed of 30 rpm.
The lathe is fitted with a Rohm 320/3 hydraulic combination 3-jaw chuck with retractable jaws and a powered face driver, allowing full-length roughing and finishing in a single setup. It also includes a Rohm hydraulic steady rest with a clamp range of 50 to 315 mm, and a servo-controlled programmable tailstock with MT#5 taper and 18 kN force.
Additional features include a mineral concrete machine base for vibration resistance, high-speed rapid movements (up to 30,000 mm/min on Z-axis), a comprehensive chip conveyor system with a capacity of 400 kg/h, and advanced coolant and filtration systems. The CNC control is a Siemens Sinumerik 840Dsl Solution Line with Ethernet and USB connectivity.
Visual inspection shows the machine exterior is clean and well-maintained, with closed safety doors and a control panel on the right side featuring an intact display and buttons. The working area is clean and intact, with two chucks and a protective curtain visible. The tailstock and tool holders show some signs of wear and minor paint chipping but no structural damage. Electrical and hydraulic components, including control boxes and cables, are present with some surface dirt but no visible damage.
This machine comes complete with static tool holders, a Marposs T18 toolsetting probe with electrical interface, a central lubrication unit, oil-mist filtration and suction system, and comprehensive documentation covering operation, programming, maintenance, and spare parts.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
| Client type | Machinery dealer |
| Active since | 2004 |
| Offers online | 40 |
| Last activity | Nov. 4, 2026 |
cnc струг VDF 450-T4/2000
Soustruh cnc VDF 450-T4/2000
VDF 450-T4/2000 cnc drejebænk
VDF 450-T4/2000 Drehmaschine CNC
cnc τόρνος VDF 450-T4/2000
VDF 450-T4/2000 cnc lathe
Torno cnc VDF 450-T4/2000
Tour cnc VDF 450-T4/2000
cnc tokarski stroj VDF 450-T4/2000
VDF 450-T4/2000 cnc eszterga
Tornio cnc VDF 450-T4/2000
cnc tekinimo staklės VDF 450-T4/2000
VDF 450-T4/2000 cnc-draaibank
Tokarka CNC VDF 450-T4/2000
Torno CNC VDF 450-T4/2000
strung cnc VDF 450-T4/2000
VDF 450-T4/2000 Токарный станок с ЧПУ
cnc strug VDF 450-T4/2000
VDF 450-T4/2000 cnc svarv
Cnc torna VDF 450-T4/2000
EN
- Languages
English (GB)