Contact us to receive an offer.
| Manufacturer | Stama |
|---|---|
| Model | MC 326 / TWIN |
| Year | 2011 |
| Location | Switzerland
|
The Stama MC 326 / TWIN is a horizontal machining center manufactured in 2011, designed for high-precision and efficient machining operations. It features a dual-spindle and dual-table configuration, allowing simultaneous machining on two workpieces to enhance productivity. The machine is equipped with a Fanuc 31i-A5 controller, supporting four axes in total, which facilitates complex machining tasks.
The worktables measure 700 mm in length and 350 mm in width, each capable of supporting a maximum load of 450 kg. The travel ranges for the axes are 520 mm along the X-axis, 360 mm along the Y-axis, and 360 mm along the Z-axis. The machine includes two T-channels per table, each with a width of 14H12 mm, for secure clamping of workpieces.
The tool changer system consists of two magazines, each holding 21 tools, accommodating tool diameters up to 88 mm, or 125 mm with free adjacent pockets. The maximum tool length is 300 mm, with a maximum tool weight of 5 kg. The spindle features an HSK-A63 nose, with a distance from spindle nose to table adjustable between 200 and 560 mm, and the distance between the two spindles is 266 mm. Spindle speeds range from 36 rpm up to 12,000 rpm, powered by an 18.5 kW spindle motor.
Rapid traverse rates reach up to 60 m/min. The machine requires a 3-phase 400 Volt, 50 Hz power supply, with a total power requirement of approximately 40 kVA. Air supply at 6 bar is needed for operation.
Additional accessories include a coolant system with high-pressure coolant delivery and coolant through spindle (CTS), a paper filter facility, and a chip conveyor for efficient chip removal. The machine's overall dimensions are approximately 3300 mm in length, width, and 3200 mm in height, with a total weight around 5600 kg.
The exterior of the machine shows signs of use and dirt marks, consistent with industrial operation. It features dual doors with windows for viewing the machining area, and the control panel is mounted on a swing arm for operator accessibility. The control panel includes a screen and numerous buttons and switches, with some wear visible on the controls. The chip conveyor system is attached at the rear and shows typical usage wear. The machine is elevated on legs, allowing easy access beneath it.
This Stama MC 326 / TWIN machining center is suitable for complex and high-volume production environments requiring dual-spindle capability and efficient tool management.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
Controller :
Fanuc 31i-A5
Number of axis total
4
Number of tables
2
Number of spindles
2
Table length
700 mm
Table width
350 mm
Number of T-channels
2
T-channel width
14H12 mm
Table load max.
450 kg
Longitudinal travel (X-axis)
520 mm
Transversal travel (y-axis)
360 mm
Vertical travel (z axis)
360 mm
Tool changer:
Number of tools
2 x 21
Tool diameter
88 mm
Diameter with free adjacent pockets
125 mm
Tool lenght
300 mm
Max. tool-weight
5 kg
Average chip-to-chip time
2.4 sec
Spindle nose: HSK-A
63
Distance spindle nose to table
200 - 560 mm
distance between spindles
266 mm
Spindle speeds:
from
36 rpm
up to
12000 rpm
Rapid traverse:
60 m/min
Air connect
6 bar
Voltage 50 Hz 3x
400 Volt
Spindle motor
18.5 kW
Total power required
40 kVA
Machine's weight about
5600 kg
Overall dimensions machine:
Length
3300 mm
Width
3300 mm
Height
3200 mm
Various accessories:
Coolant system
High pression colant device
Coolant through spindle (cts)
Paper filter facility
Chip conveyor
Please note that this description may have been translated or optimized with artificial intelligence (AI) automatically. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase.
What type of model is this Stama MC 326 TWIN?
This Stama MC 326 TWIN machining center is a horizontal model.
What year was this equipment manufactured?
This equipment was manufactured in the year 2011.
What type of machining center is this Stama MC 326 / TWIN?
This Stama MC 326 / TWIN machining center is a horizontal model.
What year was this equipment manufactured?
This equipment was manufactured in the year 2011.
What type of machine is this Stama MC 326 / TWIN?
This Stama MC 326 / TWIN is a horizontal machining center.
What year was this machining center manufactured?
This machining center was manufactured in the year 2011.
The following questions and answers are generated using artificial intelligence based on the product information available. They are provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
| Client type | Machinery dealer |
| Active since | 2014 |
| Offers online | 258 |
| Last activity | Nov. 1, 2026 |
Controller :
Fanuc 31i-A5
Number of axis total
4
Number of tables
2
Number of spindles
2
Table length
700 mm
Table width
350 mm
Number of T-channels
2
T-channel width
14H12 mm
Table load max.
450 kg
Longitudinal travel (X-axis)
520 mm
Transversal travel (y-axis)
360 mm
Vertical travel (z axis)
360 mm
Tool changer:
Number of tools
2 x 21
Tool diameter
88 mm
Diameter with free adjacent pockets
125 mm
Tool lenght
300 mm
Max. tool-weight
5 kg
Average chip-to-chip time
2.4 sec
Spindle nose: HSK-A
63
Distance spindle nose to table
200 - 560 mm
distance between spindles
266 mm
Spindle speeds:
from
36 rpm
up to
12000 rpm
Rapid traverse:
60 m/min
Air connect
6 bar
Voltage 50 Hz 3x
400 Volt
Spindle motor
18.5 kW
Total power required
40 kVA
Machine's weight about
5600 kg
Overall dimensions machine:
Length
3300 mm
Width
3300 mm
Height
3200 mm
Various accessories:
Coolant system
High pression colant device
Coolant through spindle (cts)
Paper filter facility
Chip conveyor
Please note that this description may have been translated or optimized with artificial intelligence (AI) automatically. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase.
What type of model is this Stama MC 326 TWIN?
This Stama MC 326 TWIN machining center is a horizontal model.
What year was this equipment manufactured?
This equipment was manufactured in the year 2011.
What type of machining center is this Stama MC 326 / TWIN?
This Stama MC 326 / TWIN machining center is a horizontal model.
What year was this equipment manufactured?
This equipment was manufactured in the year 2011.
What type of machine is this Stama MC 326 / TWIN?
This Stama MC 326 / TWIN is a horizontal machining center.
What year was this machining center manufactured?
This machining center was manufactured in the year 2011.
The following questions and answers are generated using artificial intelligence based on the product information available. They are provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
The Stama MC 326 / TWIN is a horizontal machining center manufactured in 2011, designed for high-precision and efficient machining operations. It features a dual-spindle and dual-table configuration, allowing simultaneous machining on two workpieces to enhance productivity. The machine is equipped with a Fanuc 31i-A5 controller, supporting four axes in total, which facilitates complex machining tasks.
The worktables measure 700 mm in length and 350 mm in width, each capable of supporting a maximum load of 450 kg. The travel ranges for the axes are 520 mm along the X-axis, 360 mm along the Y-axis, and 360 mm along the Z-axis. The machine includes two T-channels per table, each with a width of 14H12 mm, for secure clamping of workpieces.
The tool changer system consists of two magazines, each holding 21 tools, accommodating tool diameters up to 88 mm, or 125 mm with free adjacent pockets. The maximum tool length is 300 mm, with a maximum tool weight of 5 kg. The spindle features an HSK-A63 nose, with a distance from spindle nose to table adjustable between 200 and 560 mm, and the distance between the two spindles is 266 mm. Spindle speeds range from 36 rpm up to 12,000 rpm, powered by an 18.5 kW spindle motor.
Rapid traverse rates reach up to 60 m/min. The machine requires a 3-phase 400 Volt, 50 Hz power supply, with a total power requirement of approximately 40 kVA. Air supply at 6 bar is needed for operation.
Additional accessories include a coolant system with high-pressure coolant delivery and coolant through spindle (CTS), a paper filter facility, and a chip conveyor for efficient chip removal. The machine's overall dimensions are approximately 3300 mm in length, width, and 3200 mm in height, with a total weight around 5600 kg.
The exterior of the machine shows signs of use and dirt marks, consistent with industrial operation. It features dual doors with windows for viewing the machining area, and the control panel is mounted on a swing arm for operator accessibility. The control panel includes a screen and numerous buttons and switches, with some wear visible on the controls. The chip conveyor system is attached at the rear and shows typical usage wear. The machine is elevated on legs, allowing easy access beneath it.
This Stama MC 326 / TWIN machining center is suitable for complex and high-volume production environments requiring dual-spindle capability and efficient tool management.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
| Client type | Machinery dealer |
| Active since | 2014 |
| Offers online | 258 |
| Last activity | Nov. 1, 2026 |
Stama MC 326 / TWIN
Obráběcí centrum - horizontální Stama MC 326 / TWIN
Stama MC 326 / TWIN
Stama MC 326 / TWIN Bearbeitungszentrum Horizontal
Stama MC 326 / TWIN
Stama MC 326 / TWIN Machining center - horizontal
Centro de mecanizado horizontal Stama MC 326 / TWIN
Centre d'usinage horizontal Stama MC 326 / TWIN
Stama MC 326 / TWIN
Stama MC 326 / TWIN
Centro di lavoro orizzontale Stama MC 326 / TWIN
Stama MC 326 / TWIN
Stama MC 326 / TWIN
Centrum obróbcze poziome Stama MC 326 / TWIN
Stama MC 326 / TWIN
Stama MC 326 / TWIN
Stama MC 326 / TWIN Горизонтальный обрабатывающий центр
Stama MC 326 / TWIN
Stama MC 326 / TWIN
Yatay işleme merkezi Stama MC 326 / TWIN
EN
- Languages
English (GB)