Price on request
Make an offer| Power in tons | 300 T |
| Table length | 2200 mm |
| Table width | 900 mm |
| Ram stroke | 250 mm |
| Nbr of strokes/min | 36 |
| ------------------- | |
| worked hours | |
| hours under power | |
| state | as-is, where-is |
| At local norms | --------- |
| status | visible |
| Datasheet | Omec Collo di cigno 2 bielle |
| Last availability date | 04/02/2026 |
This listing features a 300-ton mechanical press manufactured by OMEC, model Collo di cigno 2 bielle, produced in 1994. The press has a robust table measuring 2200 mm in length and 900 mm in width, suitable for handling large workpieces. It operates with a ram stroke of 250 mm and can achieve up to 36 strokes per minute, making it efficient for repetitive pressing tasks.
The press utilizes an eccentric actuation system combined with link motion and a knuckle joint, which is typical for this type of mechanical press. It includes two push points and is equipped with eight guides on the slide to ensure precise movement. The slide adjustment is managed by a guided ball wedge system, allowing for accurate control of the slide position. The press also features a mechanical hydraulic overload protection system to help prevent damage under excessive loads.
Safety is addressed with yellow mesh safety guards installed on the sides of the press, providing protection during operation. Photocells are installed at the front and rear, enhancing operational safety by detecting obstructions. The press's structure includes a clearance of 700 mm for PMS and incorporates a sheet press cushion with total force capability.
The machine weighs approximately 25 tons and requires a foundation for installation. A control panel is mounted on the right side for operational control. The press shows signs of wear and dirt on its surface, with some areas of chipped paint and rust spots, indicating it has been stored or awaiting installation. The upper compartment is open, revealing some internal parts, though details are partially obscured. Multiple cables and electrical boxes are attached to the side, consistent with its mechanical and control systems.
This mechanical press is a substantial piece of equipment suitable for industrial pressing applications, offering reliable specifications and safety features as described.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
Ton: 300
Table Width (mm): 2200x900
Slide Stroke (mm): 250
Number of Strokes Min: 36
Subtype Dm Cdc: CDC2B
CE Marking: No
Condition: Working
Actuation System Eccentric Link Motion Knuckle Joint Hydraulic Screw Fly: Eccentric
Push Points: 2
Slide Number of Guides: 8
Slide Adjustment System Guided Ball Wedge: Guided
PMS Clearance mm: 700
Sheet Press Cushion Total Force Ton: Yes
Weight Ton: 25
Foundation cm: No
Front and Rear Photocells: Yes
Front and Rear Safety Guards: Yes
Mechanical Hydraulic Overload: Yes
Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase
| Client type | Machinery dealer |
| Active since | 2020 |
| Offers online | 82 |
| Last activity | April 20, 2026 |
Ton: 300
Table Width (mm): 2200x900
Slide Stroke (mm): 250
Number of Strokes Min: 36
Subtype Dm Cdc: CDC2B
CE Marking: No
Condition: Working
Actuation System Eccentric Link Motion Knuckle Joint Hydraulic Screw Fly: Eccentric
Push Points: 2
Slide Number of Guides: 8
Slide Adjustment System Guided Ball Wedge: Guided
PMS Clearance mm: 700
Sheet Press Cushion Total Force Ton: Yes
Weight Ton: 25
Foundation cm: No
Front and Rear Photocells: Yes
Front and Rear Safety Guards: Yes
Mechanical Hydraulic Overload: Yes
Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase
| Power in tons | 300 T |
| Table length | 2200 mm |
| Table width | 900 mm |
| Ram stroke | 250 mm |
| Nbr of strokes/min | 36 |
| ------------------- | |
| worked hours | |
| hours under power | |
| state | as-is, where-is |
| At local norms | --------- |
| status | visible |
| Datasheet | Omec Collo di cigno 2 bielle |
| Last availability date | 04/02/2026 |
This listing features a 300-ton mechanical press manufactured by OMEC, model Collo di cigno 2 bielle, produced in 1994. The press has a robust table measuring 2200 mm in length and 900 mm in width, suitable for handling large workpieces. It operates with a ram stroke of 250 mm and can achieve up to 36 strokes per minute, making it efficient for repetitive pressing tasks.
The press utilizes an eccentric actuation system combined with link motion and a knuckle joint, which is typical for this type of mechanical press. It includes two push points and is equipped with eight guides on the slide to ensure precise movement. The slide adjustment is managed by a guided ball wedge system, allowing for accurate control of the slide position. The press also features a mechanical hydraulic overload protection system to help prevent damage under excessive loads.
Safety is addressed with yellow mesh safety guards installed on the sides of the press, providing protection during operation. Photocells are installed at the front and rear, enhancing operational safety by detecting obstructions. The press's structure includes a clearance of 700 mm for PMS and incorporates a sheet press cushion with total force capability.
The machine weighs approximately 25 tons and requires a foundation for installation. A control panel is mounted on the right side for operational control. The press shows signs of wear and dirt on its surface, with some areas of chipped paint and rust spots, indicating it has been stored or awaiting installation. The upper compartment is open, revealing some internal parts, though details are partially obscured. Multiple cables and electrical boxes are attached to the side, consistent with its mechanical and control systems.
This mechanical press is a substantial piece of equipment suitable for industrial pressing applications, offering reliable specifications and safety features as described.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
| Client type | Machinery dealer |
| Active since | 2020 |
| Offers online | 82 |
| Last activity | April 20, 2026 |
Преса OMEC 300 тона 2 биели
Lis OMEC 300 tun 2 ojnice
OMEC 300 ton 2 stempelstang presse
OMEC-Presse 300 Tonnen 2 Pleuelstangen
Πρέσα OMEC 300 τόνων 2 ράβδοι σύνδεσης
OMEC 300 ton press with 2 connecting rods
Prensa OMEC 300 toneladas 2 bielas
Presse OMEC 300 tonnes 2 bielles
OMEC preša od 300 tona s dva klipnjače
OMEC 300 ton 2 hajtókaros prés
Pressa OMEC 300 ton 2 Bielle
OMEC 300 ton 2 švaistiklių presas
OMEC-pers 300 ton 2 drijfstangen
Prasa OMEC 300 ton 2 korbowody
Prensa OMEC 300 toneladas 2 bielas
Presă OMEC de 300 tone cu 2 biele
Пресс OMEC 300 тонн 2 шатуна
OMEC presa od 300 tona sa dva povezujuća štapa
Press OMEC 300 ton 2 vevstakar
OMEC 300 ton 2 Pistonlu Pres
EN
- Languages
English (GB)