Contact us to receive an offer.
| Manufacturer | Hedelius |
|---|---|
| Model | Rs 60 Magnum |
| Year | |
| Location | Switzerland
|
The Hedelius RS 60 Magnum is a vertical machining center equipped with a Siemens SINUMERIK controller supporting up to 5 axes, suitable for complex machining tasks. It features a circular rotary table with a diameter of 680 mm capable of handling a maximum load of 300 kg. The machine offers substantial travel ranges: 2000 mm longitudinally (X-axis), 620 mm transversally (Y-axis), and 520 mm vertically (Z-axis), with a swivel angle on the A-axis ranging from +15° to -95°. The tool magazine accommodates up to 56 tools, with a maximum tool diameter of 80 mm, length of 330 mm, and a maximum tool weight of 8 kg. Tool changes are efficient, occurring in approximately 3 seconds. The spindle uses an SK 40 DIN 69871 nose and operates steplessly from 50 to 12,000 rpm, delivering a maximum torque of 121 Nm. The feed rate ranges from 0 to 45,000 mm/min with a rapid traverse speed of 45 m/min and a maximum feed force of 7000 N. The machine requires a 400 Volt, 3-phase power supply with a total power consumption of 25 kVA. It has a noise level of 77 dB(A) and weighs approximately 11,000 kg with overall dimensions of 5400 mm length, 4300 mm width, and 3000 mm height. Included accessories are a set of toolholders, a 1250-liter coolant system with a high-pressure device operating at 20 bar, an air blast through the milling spindle, a paper filter facility, a Renishaw touch probe, a chip conveyor, an electronic handwheel, an oil mist extractor, and a full enclosure workspace cowl. The machine’s exterior shows typical signs of use, including paint wear and dirt marks. Inside the machining area, two blue vises are mounted on the rotary table along with a clamping fixture marked with a red cross. The machining area and spindle head exhibit normal wear and dirt consistent with use but appear structurally intact. The control panel is located on the right side of the machine and includes a clean and intact Siemens SINUMERIK display with a keyboard and buttons, showing machine parameters and coordinates. An air cleaning unit with visible ducting is mounted on top of the machine, contributing to workspace cleanliness. Lighting inside the machining area is functional, providing good visibility during operation.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
Controller :
Siemens Sinumerik
Number of axis total
3 / 5
Circulary table diameter
680 mm
Table load max.
300 kg
Longitudinal travel (X-axis)
2000 (600) mm
Transversal travel (y-axis)
620 mm
Vertical travel (z axis)
520 mm
Swivel angle (a-axis)
+15 / -95 °
Tool magazine number of tools
56
Tool diameter max.
80 mm
Tool lenght
330 mm
Max. tool-weight
8 kg
Time of tool changing
3 sec
Spindle nose SK
40 DIN 69871
Distance spindle nose to table
100 - 620 mm
Milling spindle speeds:
Milling spindle:
stepless
from
50 rpm
up to
12000 rpm
Torque max.
121 Nm
Feed range
0 - 45000 mm/min
Rapid traverse:
45 m/min
Max. Feed force
7000 N
Voltage 50 Hz 3x
400 Volt
Total power required
25 kVA
Time under power
37627 Hour
Operating time
15344 Hour
Noise level
77 dB (A)
Machine's weight about
11000 kg
Overall dimensions machine:
Length
5400 mm
Width
4300 mm
Height
3000 mm
Various accessories:
Set of toolholders
Coolant system
1250 l
High pression colant device
20 bar
Air blast through milling spindle
Paper filter facility
Touch Probe Renishaw
Chip conveyor
Handwheel electroinic
Oil mist extractor
Full enclosure workspace cowl
Please note that this description may have been translated or optimized with artificial intelligence (AI) automatically. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase.
| Client type | Machinery dealer |
| Active since | 2014 |
| Offers online | 258 |
| Last activity | Nov. 6, 2026 |
Controller :
Siemens Sinumerik
Number of axis total
3 / 5
Circulary table diameter
680 mm
Table load max.
300 kg
Longitudinal travel (X-axis)
2000 (600) mm
Transversal travel (y-axis)
620 mm
Vertical travel (z axis)
520 mm
Swivel angle (a-axis)
+15 / -95 °
Tool magazine number of tools
56
Tool diameter max.
80 mm
Tool lenght
330 mm
Max. tool-weight
8 kg
Time of tool changing
3 sec
Spindle nose SK
40 DIN 69871
Distance spindle nose to table
100 - 620 mm
Milling spindle speeds:
Milling spindle:
stepless
from
50 rpm
up to
12000 rpm
Torque max.
121 Nm
Feed range
0 - 45000 mm/min
Rapid traverse:
45 m/min
Max. Feed force
7000 N
Voltage 50 Hz 3x
400 Volt
Total power required
25 kVA
Time under power
37627 Hour
Operating time
15344 Hour
Noise level
77 dB (A)
Machine's weight about
11000 kg
Overall dimensions machine:
Length
5400 mm
Width
4300 mm
Height
3000 mm
Various accessories:
Set of toolholders
Coolant system
1250 l
High pression colant device
20 bar
Air blast through milling spindle
Paper filter facility
Touch Probe Renishaw
Chip conveyor
Handwheel electroinic
Oil mist extractor
Full enclosure workspace cowl
Please note that this description may have been translated or optimized with artificial intelligence (AI) automatically. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase.
The Hedelius RS 60 Magnum is a vertical machining center equipped with a Siemens SINUMERIK controller supporting up to 5 axes, suitable for complex machining tasks. It features a circular rotary table with a diameter of 680 mm capable of handling a maximum load of 300 kg. The machine offers substantial travel ranges: 2000 mm longitudinally (X-axis), 620 mm transversally (Y-axis), and 520 mm vertically (Z-axis), with a swivel angle on the A-axis ranging from +15° to -95°. The tool magazine accommodates up to 56 tools, with a maximum tool diameter of 80 mm, length of 330 mm, and a maximum tool weight of 8 kg. Tool changes are efficient, occurring in approximately 3 seconds. The spindle uses an SK 40 DIN 69871 nose and operates steplessly from 50 to 12,000 rpm, delivering a maximum torque of 121 Nm. The feed rate ranges from 0 to 45,000 mm/min with a rapid traverse speed of 45 m/min and a maximum feed force of 7000 N. The machine requires a 400 Volt, 3-phase power supply with a total power consumption of 25 kVA. It has a noise level of 77 dB(A) and weighs approximately 11,000 kg with overall dimensions of 5400 mm length, 4300 mm width, and 3000 mm height. Included accessories are a set of toolholders, a 1250-liter coolant system with a high-pressure device operating at 20 bar, an air blast through the milling spindle, a paper filter facility, a Renishaw touch probe, a chip conveyor, an electronic handwheel, an oil mist extractor, and a full enclosure workspace cowl. The machine’s exterior shows typical signs of use, including paint wear and dirt marks. Inside the machining area, two blue vises are mounted on the rotary table along with a clamping fixture marked with a red cross. The machining area and spindle head exhibit normal wear and dirt consistent with use but appear structurally intact. The control panel is located on the right side of the machine and includes a clean and intact Siemens SINUMERIK display with a keyboard and buttons, showing machine parameters and coordinates. An air cleaning unit with visible ducting is mounted on top of the machine, contributing to workspace cleanliness. Lighting inside the machining area is functional, providing good visibility during operation.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
| Client type | Machinery dealer |
| Active since | 2014 |
| Offers online | 258 |
| Last activity | Nov. 6, 2026 |
Hedelius Rs 60 Magnum
Obráběcí centrum - vertikální Hedelius Rs 60 Magnum
Hedelius Rs 60 Magnum
Hedelius Rs 60 Magnum Bearbeitungszentrum Vertikal
Hedelius Rs 60 Magnum
Hedelius Rs 60 Magnum Machining center - vertical
Centro de mecanizado vertical Hedelius Rs 60 Magnum
Centre d'usinage vertical Hedelius Rs 60 Magnum
Hedelius Rs 60 Magnum
Hedelius Rs 60 Magnum
Centro di lavoro verticale Hedelius Rs 60 Magnum
Hedelius Rs 60 Magnum
Hedelius Rs 60 Magnum
Pionowe centrum obróbcze Hedelius Rs 60 Magnum
Hedelius Rs 60 Magnum
Hedelius Rs 60 Magnum
Hedelius Rs 60 Magnum Вертикальный обрабатывающий центр
Hedelius Rs 60 Magnum
Hedelius Rs 60 Magnum
Dikey işleme merkezi Hedelius Rs 60 Magnum
EN
- Languages
English (GB)