| Manufacturer | DONGBU STEEL |
|---|---|
| Model | 3.2T |
| Year | 1993 |
| Location | South Korea
|
This industrial cut-to-length line, manufactured in 1993, is designed for processing cold rolled (CR), galvanized iron (GI), electro-galvanized iron (EGI), and pre-oiled (PO) coils. It handles materials with a tensile strength of up to 50 Kg/mm². The line accommodates coil thicknesses from 0.3 mm to 3.2 mm and coil widths ranging between 500 mm and 1,550 mm. Coils can weigh up to 20,000 kg, with an inside diameter of 508 mm and a maximum outside diameter of 2,000 mm.
The system produces sheets with widths from 500 mm to 1,550 mm and lengths from 500 mm up to 5,000 mm. The maximum piling weight is 5,000 kg. The line operates at a maximum speed of 50 meters per minute, with threading speed up to 10 meters per minute. Speed and tension are controlled via a DC control system, which also manages the overall line operation. The cutting method employed is a stop-running type using an up-cut shear. The threading standard is centered on the line, with a pass line height set at floor level plus 1,250 mm. The threading direction runs from left to right as viewed from the operation side.
Power requirements include a main control power supply of AC 440V, 60Hz, three-phase, and an operation power supply of AC 220V, 60Hz, single-phase. Hydraulic pressure is maintained normally at 70 Kg/cm², with a maximum of 100 Kg/cm², while pneumatic pressure operates normally at 5 Kg/cm², with a maximum of 7 Kg/cm².
The line composition consists of multiple components: a coil car with coil skid, uncoiler with snubber roll, coil opener, leveler with pinch roll powered by a 55 kW DC motor, loop table, side guide, feeder unit powered by a 22 kW DC motor, up-cut shear, run-out conveyor with scrap car, piler, sheet car with table lift, along with hydraulic and pneumatic equipment. Installation, dismantling, delivery, and test run services are not included but can be quoted separately.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
1. GENERAL DATA
Year of Manufacture In 1993
Raw Material CR, GI, EGI, PO COILS
Tensile Strength Max. 50Kg/mm2
Coil Thickness Min. 0.3mm ~ Max. 3.2mmT
Coil Width Min. 500mm ~ Max. 1,550mm
Coil Weight Max. 20,000Kg
Coil Inside Diameter ∅508mm
Coil Outside Diameter Max. ∅2,000mm
2. PRODUCT DATA
Sheet Width Min. 500mmW ~ Max.1,550mmW
Sheet Length Min. 500mmL ~ MAX. 5,000mmW
Piling Weight Max. 5,000Kg
3. LINE DATA
Line Speed: Max. 50m/min
Threading Speed Max. 10m/min
Speed & Tension Control DC Control
Cutting Method Stop Running Cutting Type by Up Cut Shear
Control System DC Control System
Standard of Threading Line Center
Pass Line Height FL + 1,250mm
Line Threading Direction From Left To Right (View Of The Operation Side)
4. POWER SOURCE
Main Control Power AC 440V, 60Hz, 3∅
Operation Power AC 220V, 60Hz, 1∅
Hydraulic Pressure Normal. 70Kg/Cm2
Max. 100Kg/Cm2
Pneumatic Pressure Normal. 5Kg/Cm2
Max. 7Kg/Cm2
5. LINE COMPOSITION
1. Coil Car With Coil Skid
2. Uncoiler with Snubber Roll
3. Coil Opener
4. Leveler with Pinch Roll (DC 55Kw)
5. Loop Table
6. Side Guide
7. Feeder Unit (DC 22Kw)
8. Up Cut Shear
9. Run-out Conveyor with Scrap Car
10. Piler
11. Sheet Car with Table Lift
12. Hydraulic Equipment
13. Pneumatic Equipment
Please note that this description may have been translated or optimized with artificial intelligence (AI) automatically. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase.
| Client type | Machinery manufacturer |
| Active since | 2024 |
| Offers online | 6 |
| Last activity | Nov. 5, 2026 |
1. GENERAL DATA
Year of Manufacture In 1993
Raw Material CR, GI, EGI, PO COILS
Tensile Strength Max. 50Kg/mm2
Coil Thickness Min. 0.3mm ~ Max. 3.2mmT
Coil Width Min. 500mm ~ Max. 1,550mm
Coil Weight Max. 20,000Kg
Coil Inside Diameter ∅508mm
Coil Outside Diameter Max. ∅2,000mm
2. PRODUCT DATA
Sheet Width Min. 500mmW ~ Max.1,550mmW
Sheet Length Min. 500mmL ~ MAX. 5,000mmW
Piling Weight Max. 5,000Kg
3. LINE DATA
Line Speed: Max. 50m/min
Threading Speed Max. 10m/min
Speed & Tension Control DC Control
Cutting Method Stop Running Cutting Type by Up Cut Shear
Control System DC Control System
Standard of Threading Line Center
Pass Line Height FL + 1,250mm
Line Threading Direction From Left To Right (View Of The Operation Side)
4. POWER SOURCE
Main Control Power AC 440V, 60Hz, 3∅
Operation Power AC 220V, 60Hz, 1∅
Hydraulic Pressure Normal. 70Kg/Cm2
Max. 100Kg/Cm2
Pneumatic Pressure Normal. 5Kg/Cm2
Max. 7Kg/Cm2
5. LINE COMPOSITION
1. Coil Car With Coil Skid
2. Uncoiler with Snubber Roll
3. Coil Opener
4. Leveler with Pinch Roll (DC 55Kw)
5. Loop Table
6. Side Guide
7. Feeder Unit (DC 22Kw)
8. Up Cut Shear
9. Run-out Conveyor with Scrap Car
10. Piler
11. Sheet Car with Table Lift
12. Hydraulic Equipment
13. Pneumatic Equipment
Please note that this description may have been translated or optimized with artificial intelligence (AI) automatically. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase.
This industrial cut-to-length line, manufactured in 1993, is designed for processing cold rolled (CR), galvanized iron (GI), electro-galvanized iron (EGI), and pre-oiled (PO) coils. It handles materials with a tensile strength of up to 50 Kg/mm². The line accommodates coil thicknesses from 0.3 mm to 3.2 mm and coil widths ranging between 500 mm and 1,550 mm. Coils can weigh up to 20,000 kg, with an inside diameter of 508 mm and a maximum outside diameter of 2,000 mm.
The system produces sheets with widths from 500 mm to 1,550 mm and lengths from 500 mm up to 5,000 mm. The maximum piling weight is 5,000 kg. The line operates at a maximum speed of 50 meters per minute, with threading speed up to 10 meters per minute. Speed and tension are controlled via a DC control system, which also manages the overall line operation. The cutting method employed is a stop-running type using an up-cut shear. The threading standard is centered on the line, with a pass line height set at floor level plus 1,250 mm. The threading direction runs from left to right as viewed from the operation side.
Power requirements include a main control power supply of AC 440V, 60Hz, three-phase, and an operation power supply of AC 220V, 60Hz, single-phase. Hydraulic pressure is maintained normally at 70 Kg/cm², with a maximum of 100 Kg/cm², while pneumatic pressure operates normally at 5 Kg/cm², with a maximum of 7 Kg/cm².
The line composition consists of multiple components: a coil car with coil skid, uncoiler with snubber roll, coil opener, leveler with pinch roll powered by a 55 kW DC motor, loop table, side guide, feeder unit powered by a 22 kW DC motor, up-cut shear, run-out conveyor with scrap car, piler, sheet car with table lift, along with hydraulic and pneumatic equipment. Installation, dismantling, delivery, and test run services are not included but can be quoted separately.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
| Client type | Machinery manufacturer |
| Active since | 2024 |
| Offers online | 6 |
| Last activity | Nov. 5, 2026 |
Линия за нарязване на дължина DONGBU STEEL 3,2T
Linka na řezání na délku DONGBU STEEL 3,2 t
DONGBU STEEL 3,2T længdeskæringsanlæg
DONGBU STEEL 3,2-Tonnen-Längsschneidelinie
Γραμμή κοπής κατά μήκος DONGBU STEEL 3,2T
DONGBU STEEL 3.2T cut-to-length line
Línea de corte a medida de 3,2 T de DONGBU STEEL
Ligne de découpe à longueur DONGBU STEEL 3,2 t
DONGBU STEEL 3,2 T linija za rezanje po duljini
DONGBU STEEL 3,2 tonnás hosszirányú vágóvonal
Linea di taglio a misura DONGBU STEEL da 3,2 t
„DONGBU STEEL“ 3,2 t ilgio pjovimo linija
DONGBU STEEL 3,2T-snijlijn
Linia do cięcia na wymiar DONGBU STEEL 3,2T
Linha de corte a comprimento da DONGBU STEEL de 3,2T
Linia de tăiere la lungime DONGBU STEEL de 3,2 t
Линия поперечной резки DONGBU STEEL 3,2 т
Dongbu Stil 3,2 t linija za sečenje po dužini
DONGBU STEEL 3,2 ton längdskärningslinje
DONGBU STEEL 3,2 tonluk boy kesim hattı
EN
- Languages
English (GB)