| Manufacturer | BRONX |
|---|---|
| Model | PPX.2410 |
| Year | 1968 |
| Location | India
|
Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls.
SPECIFICATION
Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only".
Maximum width 10' (3048 mm)
Maximum thickness at this width 4” (100 mm)
Maximum Thickness Otherwise 6" (150mm)
Minimum inside diameter of rolled cylinder at maximum capacity 39" (1000 mm)
Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.)
8” (200 mm)
Diameter of all rolls - 30” (810 mm)
Body length of rolls - 11’2”(3403mm)
Rolling speed - 12 f.p.m. (3600mm/min)
Main drive motor - 190 H.P. Slip Ring Type/ 720 rpm
Two bottom roll adjusting motors, each - 75* H.P. Slip Ring Type
Combined operation of swing down bearing and top roll counterbalance
- Hydraulically applied
Hydraulic power pack motor - 10 H.P.
CONE ROLLING ATTACHMENT:
To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing.
Control Gear:
Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary.
Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary.
Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station.
Solenoid valves for operating cylinders are push button operated.
NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.
Please note that this description may have been translated or optimized with artificial intelligence (AI) automatically. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase.
| Client type | Factory – small or medium company |
| Active since | 2022 |
| Offers online | 2 |
| Last activity | Oct. 29, 2026 |
Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls.
SPECIFICATION
Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only".
Maximum width 10' (3048 mm)
Maximum thickness at this width 4” (100 mm)
Maximum Thickness Otherwise 6" (150mm)
Minimum inside diameter of rolled cylinder at maximum capacity 39" (1000 mm)
Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.)
8” (200 mm)
Diameter of all rolls - 30” (810 mm)
Body length of rolls - 11’2”(3403mm)
Rolling speed - 12 f.p.m. (3600mm/min)
Main drive motor - 190 H.P. Slip Ring Type/ 720 rpm
Two bottom roll adjusting motors, each - 75* H.P. Slip Ring Type
Combined operation of swing down bearing and top roll counterbalance
- Hydraulically applied
Hydraulic power pack motor - 10 H.P.
CONE ROLLING ATTACHMENT:
To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing.
Control Gear:
Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary.
Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary.
Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station.
Solenoid valves for operating cylinders are push button operated.
NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.
Please note that this description may have been translated or optimized with artificial intelligence (AI) automatically. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase.
| Client type | Factory – small or medium company |
| Active since | 2022 |
| Offers online | 2 |
| Last activity | Oct. 29, 2026 |
Тривалова машина за огъване на листов материал BRONX PPX.2410
Tříválcová zakružovačka plechu BRONX PPX.2410
BRONX PPX.2410 3-valset pladevalsemaskine
BRONX PPX.2410 3-Walzen-Blechbiegemaschine
Κυλινδρομηχανή λαμαρίνας 3 κυλίνδρων BRONX PPX.2410
BRONX PPX.2410 3-roll plate rolling machine
Cilindros curvadores de chapa de 3 rodillos BRONX PPX.2410
Rouleuse de tôle à 3 rouleaux BRONX PPX.2410
Trovaljni valjak za savijanje lima BRONX PPX.2410
BRONX PPX.2410 Háromhengeres lemezhengerítő gép
Calandra per lamiera a 3 rulli BRONX PPX.2410
BRONX PPX.2410 3 velenų skardos valcavimo staklė
BRONX PPX.2410 3-rollen plaatwalsmachine
Walcarka do blachy 3-walcowa BRONX PPX.2410
Calandra de chapa de 3 rolos BRONX PPX.2410
Mașină de rulat tablă cu 3 role BRONX PPX.2410
BRONX PPX.2410 Трёхвалковая листогибочная машина
Trovaljni valjak za savijanje lima BRONX PPX.2410
BRONX PPX.2410 3-vals plåtvalsmaskin
3 toplu silindir büküm makinesi BRONX PPX.2410
EN
- Languages
English (GB)