Manufacturer Safan
Model B-Shear 310-6 TS100
Year 2008
Location Poland PL
Category Shears - hydraulic guillotines
Product id P00805059

€34,000

Contact the seller

You have the same machine to sell?

Add it to our catalogue for FREE

Start selling

About this seller

Client type Reseller
Active since 2016
Offers online 5
Last activity Sept. 9, 2020

Specifications

Cutting length 3100 mm
Max. thickness 6 mm
-------------------
Worked hours
Hours under power
State good
At local norms ---------
Status

Description

Lowest energy consumption
➢ 25 liters of oil in the system
➢ Controller touchscreen monitor
➢ Blade - 4 cutting edges
➢ Automatic angle setting
➢ Automatic gap setting
➢ Independent L / R drives for gap adjustment
➢ Fine adjustment of the parallelism of the bumper
➢ Low noise level
➢ Pneumatic sheet support
➢ Blade management

Safan B-Shear hydraulic guillotine shears are the next generation of HT machines built in 2000.
The high accuracy of workmanship and the unique design of the table and the hydraulic drive caused that these machines
have earned the reputation of being reliable and precise. The pump drive used in these machines is abbreviated
HT (Hybrid Technique). It is a hybrid drive where the pump is started (by an inverter) in
when the foot pedal is pressed and stops when the cut is made. Such a system allows for a significant reduction
electricity consumed, because when the machine does not cut (even for several seconds), it does not consume
energy because the pump is stopped. The hybrid system requires significantly less hydraulic oil (pump does not
works constantly, so it does not heat the oil), hence its capacity is estimated at about 25 liters. There is also no necessity
regular oil changes. Safan guillotines are distinguished by precision and versatility. Screw driven bumper
ball bearings, no play, allows for positioning with an accuracy of +/- 0.01mm, and the minimum gap is 0.04mm
allows for high-quality cutting of materials with a thickness of 0.3-0.5mm * to 6mm. Construction of the working table
allows to maintain straightness of the cut, even under heavy loads. A wide range of types available
knives of different strengths will allow you to adjust the machine to the most extreme tasks. Just like we
on all Safan machines, special emphasis is placed on ergonomics. Touch screen controller
(depending on the machine, it is mounted on the front plate of the machine or on the boom), it is intuitive
reach all machine functions. Automatic selection of the slit and cutting angle depending on the type and thickness
material and compensation of the bumper position, allows even less experienced operators to use it efficiently

machine and achieve high product quality.
SAFAN B-Shear has independent LEFT / RIGHT side control
gap. This means that the left and right machines are independent
drives. The actuators are connected in series, i.e. if from one
the cylinder pushes out the oil, it goes to the other. Hybrid Drive
causes the pump to work only when the pedal is pressed by
operator. There are only 22 liters of the SAFAN B-Shear guillotine in the overall system
oil.

The pins that support the sheet keep it in place
level, which significantly improves the quality of the cut. The cut end
the sheet metal does not fall. The cut sheet metal falls first with its end on the side
knife. The pins are pneumatically controlled.

SAFAN B-Shear has a TS-100 controller with a monochrome touch screen located on the
machine frame. Large and clear icons allow for efficient and intuitive operation of all functions. There are three
controller operation modes depending on the operator's skills: BASIC, MEDIUM and ADVANCED.

The BASIC mode allows the operator to work efficiently through
entering the size, type of material, material thickness. Machine after
after selecting these parameters, it automatically sets the cutting parameters.
Rake angle, gap size, and bumper dimensions are set
automatically, without operator intervention.

The MEDIUM mode is the most frequently used controller operating mode. In it you can
simply select the basic cutting parameters as in the mode
primary. Additionally, there are functions related to the place of the cut on
knife length and basic automatic cutting functions.
The controller allows you to decide where the cutting will take place. Operator
by moving the left and right material size limit indicators
decides where the part will cut. This way you can increase
number of cuts
And save the knife blade by evenly wearing the edges.

The EXPERT mode is the most advanced version of the controller. The operator has
programming of cutting parameters, setting correction
proposed by the software.

Please note that this description may have been translated automatically. Contact us for further information.

How does Exapro work?

Using Exapro is super easy, here is how it works

Here is a selection of similar machines

Share

Contact the seller