| Manufacturer | Quattro |
|---|---|
| Model | Peak L Plus |
| Year | |
| Location | Netherlands
|
The Quattro Peak L Plus is a large industrial PCB reflow oven designed for efficient and precise soldering processes. It features a long body equipped with multiple access panels for ease of maintenance and operation. The machine includes a control panel mounted on the left side, which is fitted with a screen and buttons for user-friendly operation and process control. An emergency stop button is conveniently located near the control panel to ensure safety during operation.
The oven's overall dimensions are approximately 6714 mm in length (including the 3-stage cooling zone), 1435 mm in width, and 1647 mm in height in delivery condition, extending up to 2233 mm when including the warning light. The inlet height is adjustable between 830 and 1030 mm to accommodate various production setups. The unit weighs around 2800 kg and is supported by 14 feet with an 80 mm diameter each, with a maximum floor loading of 750 kg/m².
Inside, the process area extends 6392.5 mm in length and includes five pre-heating zones and three peak zones equipped with six heating modules (three top and three bottom). The total heated tunnel length measures 4167 mm. The oven operates with 100% forced convection heat transfer, reaching maximum temperatures of 300 °C in the pre-heating zones and up to 350 °C in the peak zones. Temperature is monitored using NiCr-Ni sensors in the hot gas flow, with a warm-up time of approximately 30 minutes.
The transport chain conveyor supports a usable working width from 60 to 510 mm with PCB support and can handle a maximum load of 3 kg/m. The conveyor speed ranges from 0.2 to 3.0 m/min, with an average speed between 0.7 and 1.2 m/min. Exhaust air is managed through a suction pipe with a diameter of 200 mm, requiring approximately 600 to 800 m³/h of exhaust air at less than 50 °C.
The control system is the CDIAS with RT 7, and the oven includes a nitrogen supply connection with a working pressure of approximately 6 to 8 bar. Nitrogen consumption varies from about 9 m³/h in steady state to approximately 15 m³/h at full load, with readiness for a system containing 1000 ppm and nitrogen with less than 5 ppm oxygen achieved in about 15 minutes.
Power requirements include a 3-phase 230/400 V, 50 Hz supply with a maximum current consumption of 95 A per phase. Power consumption is 64 kW during heat-up and approximately 9 kW in steady state.
The machine shows signs of use, including slight discoloration and minor rust stains on the top edge, indicating previous operation but maintained condition. It is located indoors in a well-lit industrial environment with tiled flooring, suitable for integration into existing production lines.
For further information or inquiries, please do not hesitate to contact us.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
Quattro Peak L Plus in excellent condition
Specifications:
Overall dimensions
Length (with 3-stage cooling zone): 5.) 6714 mm
Width: 1435 mm
Height (in delivery condition / incl. warning light): 2.) 1647 mm / 2233 mm
Inlet height, adjustable by customer: 2.) 830 ... 1030 ±20 mm
Weight approx. 2800 kg
Number / diameter foot: 14 / 80 mm
Max. floor loading: 750 kg/m²
Process area
Length: 6392.5 mm
Pre-heating zones: 5
Peak zone (top/bottom): 3 peak zones with 6 heating modules (3 top/3 bottom)
Bottom heating modules pre-heating zones (option): 5
Heated tunnel length, total: 4167 mm
Active convection length: Length of cooling zone 1- / 2- / 3- / 4- / 5-stage: 1278.5 / 1752 / 2225.5 / 2822.5 / 3296 mm
Temperature measurement: NiCr-Ni sensors in the hot gas flow
Warm-up time: approx. 30 min.
Heat transfer: 100% forced convection
Process temperature (pre-heating zone/peak zone): max. 300 °C (pre-heating zone) / 350 °C (Peak)
Transport chain conveyor
Working width usable with PCB support: 60 ... 510 mm
Usable working width with PCB support: PIN level ... -10 mm
Pass through height (top/bottom): 30/30 mm
Max. loading: 3 kg/m
Transport mesh belt conveyor
Usable working width: 500 mm
Pass through height (top): 30 mm
Max. loading: 3 kg/m
Conveyor speed 0.2 ... 3.0 m/min
Average conveyor speed 0.7 ... 1.2 m/min.
Exhaustion 3.)
Suction pipe: 1 x Ø 200 mm
Required exhaust air at pipe (inlet): approx. 600 … 800 m3/h
Temperature of exhaust air at the pipe: < 50 °C
Internal exhaust air resistance of oven: 3 - 8 mbar
Continuous sound pressure level < 70 dB(A)
Control Unit CDIAS with RT 7
Nitrogen supply * 4.)
Connecting armature (clamped joint for Cu-pipe): R 3/8“ internal thread
Working pressure (at connecting armature): 6 ... 8 bar approx. 9 m3
N2-consumption, steady state condition and transport width 220 mm: 6.) approx. 9 m3/h
N2-consumption, full load and transport width 220 mm: 7.) approx. 15 m3/h
Readiness for the system (1000 ppm, N2 < 5 ppm O2): approx. 15 min.
Power supply
Connecting power supply: 3~N, PE 230 / 400 V, 50 Hz
Max. current consumption per phase: 95A
Power consumption during heat-up: 64 kW
Power consumption steady state condition: 1.) approx. 9 kW h
For further information please do not hesistate to contact us.
Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase
| Client type | Machinery dealer |
| Active since | 2019 |
| Offers online | 16 |
| Last activity | July 10, 2026 |
Quattro Peak L Plus in excellent condition
Specifications:
Overall dimensions
Length (with 3-stage cooling zone): 5.) 6714 mm
Width: 1435 mm
Height (in delivery condition / incl. warning light): 2.) 1647 mm / 2233 mm
Inlet height, adjustable by customer: 2.) 830 ... 1030 ±20 mm
Weight approx. 2800 kg
Number / diameter foot: 14 / 80 mm
Max. floor loading: 750 kg/m²
Process area
Length: 6392.5 mm
Pre-heating zones: 5
Peak zone (top/bottom): 3 peak zones with 6 heating modules (3 top/3 bottom)
Bottom heating modules pre-heating zones (option): 5
Heated tunnel length, total: 4167 mm
Active convection length: Length of cooling zone 1- / 2- / 3- / 4- / 5-stage: 1278.5 / 1752 / 2225.5 / 2822.5 / 3296 mm
Temperature measurement: NiCr-Ni sensors in the hot gas flow
Warm-up time: approx. 30 min.
Heat transfer: 100% forced convection
Process temperature (pre-heating zone/peak zone): max. 300 °C (pre-heating zone) / 350 °C (Peak)
Transport chain conveyor
Working width usable with PCB support: 60 ... 510 mm
Usable working width with PCB support: PIN level ... -10 mm
Pass through height (top/bottom): 30/30 mm
Max. loading: 3 kg/m
Transport mesh belt conveyor
Usable working width: 500 mm
Pass through height (top): 30 mm
Max. loading: 3 kg/m
Conveyor speed 0.2 ... 3.0 m/min
Average conveyor speed 0.7 ... 1.2 m/min.
Exhaustion 3.)
Suction pipe: 1 x Ø 200 mm
Required exhaust air at pipe (inlet): approx. 600 … 800 m3/h
Temperature of exhaust air at the pipe: < 50 °C
Internal exhaust air resistance of oven: 3 - 8 mbar
Continuous sound pressure level < 70 dB(A)
Control Unit CDIAS with RT 7
Nitrogen supply * 4.)
Connecting armature (clamped joint for Cu-pipe): R 3/8“ internal thread
Working pressure (at connecting armature): 6 ... 8 bar approx. 9 m3
N2-consumption, steady state condition and transport width 220 mm: 6.) approx. 9 m3/h
N2-consumption, full load and transport width 220 mm: 7.) approx. 15 m3/h
Readiness for the system (1000 ppm, N2 < 5 ppm O2): approx. 15 min.
Power supply
Connecting power supply: 3~N, PE 230 / 400 V, 50 Hz
Max. current consumption per phase: 95A
Power consumption during heat-up: 64 kW
Power consumption steady state condition: 1.) approx. 9 kW h
For further information please do not hesistate to contact us.
Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase
The Quattro Peak L Plus is a large industrial PCB reflow oven designed for efficient and precise soldering processes. It features a long body equipped with multiple access panels for ease of maintenance and operation. The machine includes a control panel mounted on the left side, which is fitted with a screen and buttons for user-friendly operation and process control. An emergency stop button is conveniently located near the control panel to ensure safety during operation.
The oven's overall dimensions are approximately 6714 mm in length (including the 3-stage cooling zone), 1435 mm in width, and 1647 mm in height in delivery condition, extending up to 2233 mm when including the warning light. The inlet height is adjustable between 830 and 1030 mm to accommodate various production setups. The unit weighs around 2800 kg and is supported by 14 feet with an 80 mm diameter each, with a maximum floor loading of 750 kg/m².
Inside, the process area extends 6392.5 mm in length and includes five pre-heating zones and three peak zones equipped with six heating modules (three top and three bottom). The total heated tunnel length measures 4167 mm. The oven operates with 100% forced convection heat transfer, reaching maximum temperatures of 300 °C in the pre-heating zones and up to 350 °C in the peak zones. Temperature is monitored using NiCr-Ni sensors in the hot gas flow, with a warm-up time of approximately 30 minutes.
The transport chain conveyor supports a usable working width from 60 to 510 mm with PCB support and can handle a maximum load of 3 kg/m. The conveyor speed ranges from 0.2 to 3.0 m/min, with an average speed between 0.7 and 1.2 m/min. Exhaust air is managed through a suction pipe with a diameter of 200 mm, requiring approximately 600 to 800 m³/h of exhaust air at less than 50 °C.
The control system is the CDIAS with RT 7, and the oven includes a nitrogen supply connection with a working pressure of approximately 6 to 8 bar. Nitrogen consumption varies from about 9 m³/h in steady state to approximately 15 m³/h at full load, with readiness for a system containing 1000 ppm and nitrogen with less than 5 ppm oxygen achieved in about 15 minutes.
Power requirements include a 3-phase 230/400 V, 50 Hz supply with a maximum current consumption of 95 A per phase. Power consumption is 64 kW during heat-up and approximately 9 kW in steady state.
The machine shows signs of use, including slight discoloration and minor rust stains on the top edge, indicating previous operation but maintained condition. It is located indoors in a well-lit industrial environment with tiled flooring, suitable for integration into existing production lines.
For further information or inquiries, please do not hesitate to contact us.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
| Client type | Machinery dealer |
| Active since | 2019 |
| Offers online | 16 |
| Last activity | July 10, 2026 |
PCB Reflow пещ Quattro Peak L Plus
Přeformátovácí pec na PCB Quattro Peak L Plus
Quattro Peak L Plus PCB Reflow ovn
Quattro Peak L Plus PCB Reflow Öfen
Φούρνος ανανέωσης PCB Quattro Peak L Plus
Quattro Peak L Plus PCB Reflow oven
Horno de reflujo PCB Quattro Peak L Plus
Four à refusion PCB Quattro Peak L Plus
PCB Reflow pećnica Quattro Peak L Plus
Quattro Peak L Plus PCB Reflow sütő
Forno di rifusione Quattro Peak L Plus
PCB Reflow orkaitė Quattro Peak L Plus
Quattro Peak L Plus PCB Reflow-oven
Piec przelotowy PCB Quattro Peak L Plus
Forno de refluxo PCB Quattro Peak L Plus
Cuptor PCB Reflow Quattro Peak L Plus
Quattro Peak L Plus Решетчатая печь для печатной платы
PCB Reflov peć Quattro Peak L Plus
Quattro Peak L Plus PCB Reflow ugn
PCB reflow fırını Quattro Peak L Plus
EN
- Languages
English (GB)