Used injection moulding machines for sale 1455

Subcategories


Clamping force 1000 T
Shot volume 4372 cm³
Mould size 1200
Screw diameter 95 mm
Robot interface

Clamping force 1800 T
Tie bar spacing (H) 570 mm
Shot volume 358 cm³
Screw diameter 45 mm
Tie bar spacing (V) 520 mm
Pressure on material 2116 bar

Clamping force 1600 T
Tie bar spacing (H) 520 mm
Shot volume 442 cm³
Screw diameter 50 mm
Tie bar spacing (V) 520 mm
Pressure on material 1740 bar

Clamping force 160 T
Tie bar spacing (H) 520 mm
Shot volume 491 cm³
Screw diameter 50 mm
Tie bar spacing (V) 520 mm
Shot weight 446 g

Clamping force 550 T
Tie bar spacing (H) 930 mm
Shot volume 2128 cm³
Screw diameter 85 mm
Tie bar spacing (V) 930 mm
Pressure on material 1418 bar

Clamping force 550 T
Tie bar spacing (H) 930 mm
Shot volume 1885 cm³
Screw diameter 85 mm
Tie bar spacing (V) 930 mm
Pressure on material 1587 bar

Clamping force 750 T
Tie bar spacing (H) 1100 mm
Shot volume 4546 cm³
Screw diameter 105 mm
Tie bar spacing (V) 1100 mm
Pressure on material 1509 bar

Clamping force 650 T
Tie bar spacing (H) 1000 mm
Shot volume 3338 cm³
Screw diameter 100 mm
Tie bar spacing (V) 1000 mm
Shot weight 3038 g

Clamping force 1000 T
Tie bar spacing (H) 1400 mm
Shot volume 5655 cm³
Screw diameter 120 mm
Tie bar spacing (V) 1120 mm
Shot weight 5146 g

Clamping force 50 T
Tie bar spacing (H) 320 mm
Shot volume 74 cm³
Screw diameter 30 mm
Tie bar spacing (V) 320 mm
Shot weight 68 g

Clamping force 150 T
Tie bar spacing (H) 460 mm
Shot volume 422 cm³
Screw diameter 50 mm
Tie bar spacing (V) 460 mm
Shot weight 397 g

Clamping force 130 T
Tie bar spacing (H) 470 mm
Shot volume 427 cm³
Screw diameter 55 mm
Tie bar spacing (V) 470 mm
Shot weight 360 g

Clamping force 100 T
Tie bar spacing (H) 420 mm
Shot volume 139 cm³
Screw diameter 35 mm
Tie bar spacing (V) 420 mm
Shot weight 127 g

Clamping force 480 T
Tie bar spacing (H) 800 mm
Shot volume 1760 cm³
Screw diameter 80 mm
Tie bar spacing (V) 710 mm
Shot weight 1970 g

Clamping force 900 T
Tie bar spacing (H) 1025 mm
Shot volume 4546 cm³
Screw diameter 105 mm
Tie bar spacing (V) 1025 mm
Pressure on material 1509 bar

Clamping force 130 T
Tie bar spacing (H) 470 mm
Shot volume 353 cm³
Screw diameter 50 mm
Tie bar spacing (V) 470 mm
Pressure on material 2080 bar

Clamping force 150 T
Tie bar spacing (H) 500 mm
Shot volume 231 cm³
Screw diameter 40 mm
Tie bar spacing (V) 500 mm
Pressure on material 1855 bar

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale