Used injection moulding machines for sale 1391

Subcategories


Clamping force 200 T
Equipped with robot Yes
Mould size
Screw diameter 40 mm
Robot interface Robot Wittmann W602

Clamping force 420 T
Tie bar spacing (H) 800 mm
Shot volume 519 cm³
Screw diameter 55 mm
Tie bar spacing (V) 800 mm
Pressure on material 2380 bar

Clamping force 350 T
Tie bar spacing (H) 710 mm
Shot volume 358 cm³
Screw diameter 45 mm
Tie bar spacing (V) 630 mm
Pressure on material 2402 bar

Clamping force 1500 T
Shot volume 5797 cm³
Robot interface Wittman Demag
Screw diameter 110 mm
Equipped with robot Yes
Number of cores 4

Clamping force 1500 T
Tie bar spacing (H) 1530 mm
Platen length 2360 mm
Screw diameter 105 mm
Tie bar spacing (V) 1275 mm
Platen width 2110 mm

Clamping force 150 T
Shot volume 217 cm³
Platen length 780 mm
Screw diameter 40 mm
Shot weight 198 g
Platen width 790 mm

Clamping force 1000 T
Tie bar spacing (H) 1250 mm
Shot volume 6898 cm³
Screw diameter 120 mm
Tie bar spacing (V) 1000 mm
Robot interface

Clamping force 240 T
Shot volume 1000 cm³
Platen width 2000 mm
Screw diameter 75 mm
Platen length 9200 mm
Bi-metal screw Yes

Clamping force 200 T
Tie bar spacing (H) 570 mm
Shot volume 471 cm³
Screw diameter 50 mm
Tie bar spacing (V) 570 mm
Pressure on material 2047 bar

Clamping force 800 T
Tie bar spacing (H) 1170 mm
Shot volume 2740 cm³
Screw diameter 90 mm
Tie bar spacing (V) 1000 mm
Pressure on material 1910 bar

Clamping force 200 T
Shot volume 1357 cm³
Pressure on material 1330 bar
Screw diameter 80 mm
Shot weight 1222 g
Platen length 820 mm

Clamping force 50 T
Tie bar spacing (H) 320 mm
Shot volume 144 cm³
Screw diameter 35 mm
Tie bar spacing (V) 320 mm
Equipped with robot Yes

Clamping force 110 T
Tie bar spacing (H) 400 mm
Shot volume 95 cm³
Screw diameter 28 mm
Tie bar spacing (V) 400 mm
Platen length 425 mm

Clamping force 40 T
Tie bar spacing (H) 280 mm
Shot volume 95 cm³
Screw diameter 28 mm
Tie bar spacing (V) 315 mm
Platen length 425 mm

Clamping force 110 T
Tie bar spacing (H) 470 mm
Shot volume 204 cm³
Screw diameter 40 mm
Tie bar spacing (V) 470 mm
Platen length 745 mm

Clamping force 80 T
Tie bar spacing (H) 400 mm
Shot volume 160 cm³
Screw diameter 90 mm
Tie bar spacing (V) 400 mm
Platen length 560 mm

Clamping force 45 T
Shot volume 99 cm³
Platen length 450 mm
Screw diameter 30 mm
Pressure on material 2210 bar
Platen width 500 mm

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale