Used injection moulding machines for sale 1370

Subcategories


Clamping force 220 T
Tie bar spacing (V) 585 mm
Robot interface
Tie bar spacing (H) 585 mm
Shot weight 575 g
Mould size

Clamping force 110 T
Tie bar spacing (V) 470 mm
Robot interface
Tie bar spacing (H) 470 mm
Shot weight 357 g
Mould size

Clamping force 240 T
Tie bar spacing (H) 560 mm
Shot volume 792 cm³
Screw diameter 60 mm
Tie bar spacing (V) 560 mm
Platen length 880 mm

Clamping force 100 T
Tie bar spacing (H) 370 mm
Shot weight 121 g
Screw diameter 35 mm
Tie bar spacing (V) 370 mm
Robot interface

Clamping force 190 T
Shot weight 334 g
Mould size
Screw diameter 45 mm
Robot interface

Clamping force 80 T
Shot volume 168 cm³
Platen length 660 mm
Screw diameter 35 mm
Pressure on material 2020 bar
Platen width 660 mm

Clamping force 140 T
Tie bar spacing (H) 430 mm
Shot volume 220 cm³
Screw diameter 40 mm
Tie bar spacing (V) 430 mm
Pressure on material 2100 bar

Clamping force 420 T
Tie bar spacing (H) 800 mm
Shot volume 1212 cm³
Screw diameter 70 mm
Tie bar spacing (V) 710 mm
Equipped with robot Yes

Clamping force 200 T
Tie bar spacing (H) 560 mm
Shot volume 523 cm³
Screw diameter 55 mm
Tie bar spacing (V) 560 mm
Robot interface

Clamping force 180 T
Equipped with robot Yes
Number of cores 4
Screw diameter 45 mm
Robot interface
Mould size

Tie bar spacing (H) 500 mm
Shot weight 278 g
Number of cores 5
Tie bar spacing (V) 500 mm
Robot interface
Opening of the press 1000 mm

Clamping force 780 T
Tie bar spacing (H) 980 mm
Shot weight 3.145 g
Screw diameter 100 mm
Tie bar spacing (V) 980 mm
Pressure on material 1840 bar

Clamping force 1350 T
Tie bar spacing (H) 1700 mm
Shot volume 3544 cm³
Screw diameter 95 mm
Tie bar spacing (V) 1350 mm
Shot weight 3500 g

Clamping force 40 T
Tie bar spacing (H) 280 mm
Shot volume 95 cm³
Screw diameter 28 mm
Tie bar spacing (V) 315 mm
Platen length 425 mm

Clamping force 75 T
Tie bar spacing (H) 320 mm
Shot weight 158 g
Screw diameter 40 mm
Tie bar spacing (V) 320 mm
Pressure on material 1150 bar

Clamping force 75 T
Tie bar spacing (H) 320 mm
Shot weight 158 g
Screw diameter 40 mm
Tie bar spacing (V) 320 mm
Pressure on material 1150 bar

Clamping force 35 T
Tie bar spacing (H) 270 mm
Shot weight 40 g
Screw diameter 25 mm
Tie bar spacing (V) 270 mm
Pressure on material 1550 bar

Clamping force 25 T
Tie bar spacing (H) 221 mm
Shot weight 41 g
Screw diameter 25 mm
Tie bar spacing (V) 221 mm
Pressure on material 1250 bar

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale