Used injection moulding machines for sale 16

Subcategories


Clamping force 1200 T
Tie bar spacing (H) 1200 mm
Opening of the press 1500 mm
Screw diameter 133 mm
Tie bar spacing (V) 1200 mm

Clamping force 660 T
Tie bar spacing (H) 900 mm
Shot volume 4255 cm³
Screw diameter 115 mm
Tie bar spacing (V) 900 mm
Pressure on material 1480 bar

Clamping force 150 T
Tie bar spacing (H) 470 mm
Shot volume 499 cm³
Screw diameter 52 mm
Tie bar spacing (V) 470 mm
Shot weight 474 g

Clamping force 100 T
Tie bar spacing (H) 425 mm
Shot volume 374 cm³
Screw diameter 45 mm
Tie bar spacing (V) 425 mm
Shot weight 355 g

Clamping force 1200 T
Tie bar spacing (H) 1200 mm
Shot volume 8336 cm³
Screw diameter 133 mm
Tie bar spacing (V) 1200 mm
Shot weight 7919 g

Clamping force 330 T
Tie bar spacing (H) 630 mm
Shot weight 950 g
Screw diameter 72 mm
Tie bar spacing (V) 630 mm
Mould size 200

Clamping force 550 T
Tie bar spacing (H) 830 mm
Shot volume 2400 cm³
Screw diameter 98 mm
Tie bar spacing (V) 830 mm
Shot weight 1785 g

Clamping force 330 T
Tie bar spacing (H) 630 mm
Shot weight 900 g
Screw diameter 62 mm
Tie bar spacing (V) 630 mm

Clamping force 550 T
Tie bar spacing (V) 830 mm
Tie bar spacing (H) 830 mm

Clamping force 440 T
Tie bar spacing (H) 830 mm
Shot volume 2494 cm³
Screw diameter 84 mm
Tie bar spacing (V) 830 mm
Shot weight 2369 g

Clamping force 550 T
Tie bar spacing (H) 830 mm
Shot volume 2640 cm³
Screw diameter 98 mm
Tie bar spacing (V) 830 mm
Opening of the press 850 mm

Clamping force 440 T
Tie bar spacing (H) 830 mm
Shot volume 2494 cm³
Screw diameter 84 mm
Tie bar spacing (V) 830 mm
Shot weight 2369 g

Clamping force 320 T
Tie bar spacing (H) 630 mm
Shot weight 560 g
Screw diameter 52 mm
Tie bar spacing (V) 630 mm
Equipped with robot Yes

Clamping force 330 T
Tie bar spacing (H) 630 mm
Shot volume 1283 cm³
Screw diameter 72 mm
Tie bar spacing (V) 630 mm
Shot weight 1218 g

Clamping force 440 T
Tie bar spacing (H) 830 mm
Shot volume 2494 cm³
Screw diameter 84 mm
Tie bar spacing (V) 830 mm
Shot weight 2369 g

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale