Used injection moulding machines for sale 45

Subcategories


Clamping force 160 T
Tie bar spacing (H) 450 mm
Shot volume 360 cm³
Screw diameter 32 mm
Tie bar spacing (V) 510 mm
Robot interface

Clamping force 370 T
Tie bar spacing (H) 710 mm
Shot volume 1175 cm³
Screw diameter 70 mm
Tie bar spacing (V) 630 mm
Shot weight 1060 g

Clamping force 40 T
Tie bar spacing (H) 255 mm
Shot volume 56 cm³
Screw diameter 25 mm
Tie bar spacing (V) 255 mm
Equipped with robot Yes

Clamping force 320 T
Tie bar spacing (H) 630 mm
Shot volume 1175 cm³
Screw diameter 70 mm
Tie bar spacing (V) 570 mm
Equipped with robot Yes

Clamping force 1000 T
Tie bar spacing (H) 1250 mm
Shot volume 6898 cm³
Screw diameter 120 mm
Tie bar spacing (V) 1000 mm
Robot interface

Clamping force 70 T
Tie bar spacing (H) 360 mm
Shot volume 120 cm³
Screw diameter 32 mm
Tie bar spacing (V) 315 mm
Equipped with robot Yes

Clamping force 370 T
Tie bar spacing (H) 730 mm
Shot volume 2400 cm³
Screw diameter 100 mm
Tie bar spacing (V) 710 mm
Mould size 750

Clamping force 150 T
Tie bar spacing (H) 450 mm
Shot volume 622 cm³
Screw diameter 60 mm
Tie bar spacing (V) 450 mm
Mould size 525

Clamping force 40 T
Shot weight 109 g
Mould size
Screw diameter 32 mm
Robot interface

Clamping force 130 T
Tie bar spacing (H) 410 mm
Shot volume 303 cm³
Screw diameter 45 mm
Tie bar spacing (V) 410 mm
Equipped with robot Yes

Clamping force 210 T
Tie bar spacing (H) 570 mm
Pressure on material 1700 bar
Screw diameter 52 mm
Tie bar spacing (V) 510 mm
Platen length 870 mm

Clamping force 260 T
Tie bar spacing (H) 540 mm
Shot volume 791 cm³
Screw diameter 60 mm
Tie bar spacing (V) 540 mm
Equipped with robot Yes

Clamping force 430 T
Tie bar spacing (H) 680 mm
Shot volume 1810 cm³
Screw diameter 80 mm
Tie bar spacing (V) 760 mm
Pressure on material 1615 bar

Clamping force 160 T
Tie bar spacing (H) 450 mm
Shot volume 360 cm³
Screw diameter 45 mm
Tie bar spacing (V) 510 mm
Pressure on material 1700 bar

Clamping force 100 T
Tie bar spacing (H) 400 mm
Shot volume 270 cm³
Screw diameter 40 mm
Tie bar spacing (V) 400 mm
Shot weight 240 g

Clamping force 40 T
Tie bar spacing (H) 255 mm
Shot volume 56 cm³
Screw diameter 25 mm
Tie bar spacing (V) 255 mm
Robot interface

Clamping force 370 T
Tie bar spacing (H) 710 mm
Shot volume 1620 cm³
Screw diameter 70 mm
Tie bar spacing (V) 630 mm
Shot weight 965 g

Clamping force 830 T
Tie bar spacing (H) 1140 mm
Shot volume 3530 cm³
Screw diameter 100 mm
Tie bar spacing (V) 1020 mm
Shot weight 3700 g

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale