Used injection moulding machines for sale 34

Subcategories


Clamping force 400 T
Tie bar spacing (H) 725 mm
Shot volume 1465 cm³
Screw diameter 70 mm
Tie bar spacing (V) 725 mm
Pressure on material 1500 bar

Clamping force 200 T
Tie bar spacing (H) 540 mm
Shot volume 617 cm³
Screw diameter 55 mm
Tie bar spacing (V) 540 mm
Pressure on material 1760 bar

Clamping force 140 T
Tie bar spacing (H) 540 mm
Shot volume 617 cm³
Screw diameter 55 mm
Tie bar spacing (V) 540 mm
Platen length 810 mm

Clamping force 140 T
Tie bar spacing (H) 465 mm
Robot interface
Screw diameter 50 mm
Tie bar spacing (V) 465 mm
Mould size

Clamping force 2500 T
Tie bar spacing (H) 2200 mm
Shot volume 23520 cm³
Screw diameter 190 mm
Tie bar spacing (V) 1800 mm
Shot weight 20698 g

Clamping force 900 T
Tie bar spacing (H) 840 mm
Shot volume 3000 cm³
Screw diameter 90 mm
Tie bar spacing (V) 840 mm
Pressure on material 1400 bar

Clamping force 250 T
Shot weight 2000 g
Platen width 580 mm
Shot volume 1500 cm³
Platen length 730 mm
Robot interface

Clamping force 190 T
Tie bar spacing (H) 540 mm
Shot volume 617 cm³
Screw diameter 55 mm
Tie bar spacing (V) 540 mm
Pressure on material 1760 bar

Clamping force 200 T
Tie bar spacing (H) 540 mm
Shot volume 617 cm³
Screw diameter 55 mm
Tie bar spacing (V) 540 mm
Shot weight 540 g

Screw diameter 50 mm
Tie bar spacing (V) 420 mm
Pressure on material 1480 bar
Tie bar spacing (H) 420 mm
Shot volume 412 cm³
Platen length 640 mm

Clamping force 200 T
Tie bar spacing (H) 540 mm
Shot volume 617 cm³
Screw diameter 55 mm
Tie bar spacing (V) 540 mm
Bi-metal screw No

Clamping force 100 T
Tie bar spacing (H) 400 mm
Shot volume 238 cm³
Screw diameter 45 mm
Tie bar spacing (V) 400 mm
Bi-metal screw No

Clamping force 50 T
Tie bar spacing (H) 275 mm
Shot volume 84 cm³
Screw diameter 30 mm
Tie bar spacing (V) 275 mm
Bi-metal screw No

Year: -

Location: Italy

€15,000


Clamping force 190 T
Tie bar spacing (H) 480 mm
Shot volume 617 cm³
Screw diameter 55 mm
Tie bar spacing (V) 480 mm
Bi-metal screw No

Clamping force 200 T
Tie bar spacing (H) 540 mm
Shot volume 617 cm³
Screw diameter 55 mm
Tie bar spacing (V) 540 mm
Shot weight 540 g

Clamping force 200 T
Tie bar spacing (H) 540 mm
Shot volume 617 cm³
Screw diameter 55 mm
Tie bar spacing (V) 540 mm
Shot weight 540 g

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale