Used injection moulding machines for sale 128

Subcategories


Clamping force 650 T
Tie bar spacing (H) 1000 mm
Shot volume 2835 cm³
Screw diameter 95 mm
Tie bar spacing (V) 900 mm
Pressure on material 1832 bar

Clamping force 100 T
Tie bar spacing (H) 400 mm
Robot interface 1000-400
Screw diameter 40 mm
Tie bar spacing (V) 400 mm
Mould size

Clamping force 200 T
Tie bar spacing (H) 560 mm
Shot volume 399 cm³
Screw diameter 50 mm
Tie bar spacing (V) 560 mm
Shot weight 0 g

Clamping force 200 T
Tie bar spacing (H) 560 mm
Equipped with robot No
Screw diameter 45 mm
Tie bar spacing (V) 560 mm
Robot interface OUI

Clamping force 50 T
Tie bar spacing (H) 355 mm
Shot volume 106 cm³
Screw diameter 30 mm
Tie bar spacing (V) 355 mm
Pressure on material 1990 bar

Clamping force 150 T
Shot volume 323 cm³
Platen width 500 mm
Screw diameter 45 mm
Platen length 500 mm
Equipped with robot Yes

Clamping force 110 T
Tie bar spacing (H) 420 mm
Shot volume 292 cm³
Screw diameter 45 mm
Tie bar spacing (V) 420 mm
Robot interface Euromap 1100-430

Clamping force 50 T
Tie bar spacing (H) 355 mm
Shot volume 106 cm³
Screw diameter 30 mm
Tie bar spacing (V) 355 mm
Equipped with robot Yes

Clamping force 80 T
Tie bar spacing (H) 400 mm
Number of cores 1
Screw diameter 40 mm
Tie bar spacing (V) 400 mm

Clamping force 60 T
Tie bar spacing (H) 420 mm
Shot volume 61 cm³
Screw diameter 25 mm
Tie bar spacing (V) 420 mm
Shot weight 52 g

Clamping force 50 T
Tie bar spacing (H) 355 mm
Shot volume 144 cm³
Screw diameter 35 mm
Tie bar spacing (V) 355 mm
Shot weight 128 g

Clamping force 80 T
Tie bar spacing (H) 420 mm
Shot volume 168.3 cm³
Screw diameter 35 mm
Tie bar spacing (V) 420 mm
Shot weight 149 g

Clamping force 350 T
Tie bar spacing (H) 710 mm
Shot volume 1210 cm³
Screw diameter 70 mm
Tie bar spacing (V) 630 mm
Shot weight 1090 g

Clamping force 150 T
Tie bar spacing (H) 500 mm
Shot volume 231 cm³
Screw diameter 40 mm
Tie bar spacing (V) 500 mm
Pressure on material 1855 bar

Clamping force 50 T
Tie bar spacing (H) 370 mm
Shot volume 106 cm³
Screw diameter 30 mm
Tie bar spacing (V) 370 mm
Pressure on material 1995 bar

Clamping force 80 T
Equipped with robot Yes
Number of heating zones 1
Screw diameter 40 mm
Robot interface Euromap 800-400
Mould size

Clamping force 420 T
Tie bar spacing (H) 800 mm
Shot volume 1212 cm³
Screw diameter 70 mm
Tie bar spacing (V) 710 mm
Equipped with robot Yes

Screw diameter 30 mm
Tie bar spacing (V) 400 mm
Shot weight 94 g
Tie bar spacing (H) 400 mm
Shot volume 106 cm³
Pressure on material 1900 bar

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale