Used injection moulding machines for sale 23

Subcategories


Clamping force 55 T
Shot volume 73.9 cm³
Pressure on material 2778 bar
Screw diameter 28 mm
Shot weight 71.1 g
Platen length 565 mm

Clamping force 30 T
Tie bar spacing (H) 280 mm
Shot volume 72 cm³
Screw diameter 32 mm
Tie bar spacing (V) 254 mm
Shot weight 64 g

Clamping force 22 T
Tie bar spacing (H) 254 mm
Shot volume 64 cm³
Screw diameter 32 mm
Tie bar spacing (V) 254 mm
Shot weight 57 g

Clamping force 90 T
Tie bar spacing (H) 430 mm
Shot volume 262.4 cm³
Screw diameter 48 mm
Tie bar spacing (V) 360 mm
Shot weight 236 g

Clamping force 55 T
Tie bar spacing (H) 360 mm
Shot volume 166.3 cm³
Screw diameter 42 mm
Tie bar spacing (V) 335 mm
Shot weight 150 g

Clamping force 22 T
Tie bar spacing (H) 254 mm
Shot volume 49 cm³
Screw diameter 28 mm
Tie bar spacing (V) 254 mm
Shot weight 44 g

Clamping force 90 T
Tie bar spacing (H) 430 mm
Shot weight 193 g
Screw diameter 42 mm
Tie bar spacing (V) 360 mm
Pressure on material 1724 bar

Clamping force 90 T
Tie bar spacing (H) 430 mm
Shot weight 193 g
Screw diameter 42 mm
Tie bar spacing (V) 360 mm
Pressure on material 1724 bar

Clamping force 90 T
Tie bar spacing (H) 430 mm
Shot weight 193 g
Screw diameter 42 mm
Tie bar spacing (V) 360 mm
Pressure on material 1724 bar

Clamping force 90 T
Tie bar spacing (H) 430 mm
Shot weight 193 g
Screw diameter 42 mm
Tie bar spacing (V) 360 mm
Pressure on material 1724 bar

Clamping force 90 T
Tie bar spacing (H) 430 mm
Shot weight 193 g
Screw diameter 42 mm
Tie bar spacing (V) 360 mm
Pressure on material 1724 bar

Clamping force 90 T
Tie bar spacing (H) 430 mm
Shot weight 193 g
Screw diameter 42 mm
Tie bar spacing (V) 360 mm
Pressure on material 1724 bar

Clamping force 90 T
Tie bar spacing (H) 430 mm
Shot weight 193 g
Screw diameter 42 mm
Tie bar spacing (V) 430 mm
Pressure on material 1724 bar

Clamping force 50 T
Screw diameter 0 mm

Clamping force 15 T
Robot interface
Screw diameter 22 mm
Mould size

Clamping force 22 T
Shot volume 30 cm³
Platen length 440 mm
Screw diameter 22 mm
Pressure on material 3320 bar
Platen width 240 mm

Clamping force 22 T
Tie bar spacing (H) 254 mm
Shot weight 28 g
Screw diameter 22 mm
Tie bar spacing (V) 254 mm
Pressure on material 1732 bar

Clamping force 22 T
Tie bar spacing (H) 254 mm
Shot weight 28 g
Screw diameter 22 mm
Tie bar spacing (V) 254 mm
Pressure on material 1732 bar

Clamping force 22 T
Tie bar spacing (H) 254 mm
Shot volume 30 cm³
Screw diameter 22 mm
Tie bar spacing (V) 254 mm
Shot weight 27 g

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale