Used injection moulding machines for sale 1220

Subcategories


Clamping force 220 T
Shot volume 735 cm³
Platen length 860 mm
Screw diameter 60 mm
Shot weight 676 g
Platen width 830 mm

Clamping force 750 T
Tie bar spacing (H) 1100 mm
Shot volume 4546 cm³
Screw diameter 105 mm
Tie bar spacing (V) 1100 mm
Pressure on material 1509 bar

Clamping force 80 T
Tie bar spacing (H) 660 mm
Shot volume 201 cm³
Screw diameter 40 mm
Tie bar spacing (V) 560 mm
Platen length 450 mm

Clamping force 175 T
Tie bar spacing (H) 510 mm
Shot volume 201 cm³
Screw diameter 40 mm
Tie bar spacing (V) 510 mm
Platen length 450 mm

Clamping force 130 T
Tie bar spacing (H) 470 mm
Shot volume 182 cm³
Screw diameter 40 mm
Tie bar spacing (V) 470 mm
Pressure on material 2120 bar

Clamping force 650 T
Tie bar spacing (H) 1000 mm
Shot volume 2835 cm³
Screw diameter 95 mm
Tie bar spacing (V) 900 mm
Pressure on material 1832 bar

Clamping force 35 T
Tie bar spacing (H) 320 mm
Shot volume 38 cm³
Screw diameter 22 mm
Tie bar spacing (V) 320 mm
Shot weight 35 g

Clamping force 150 T
Tie bar spacing (H) 470 mm
Shot volume 166 cm³
Screw diameter 40 mm
Tie bar spacing (V) 470 mm
Pressure on material 2120 bar

Clamping force 330 T
Tie bar spacing (H) 660 mm
Shot volume 1011 cm³
Screw diameter 60 mm
Tie bar spacing (V) 600 mm
Pressure on material 2133 bar

Clamping force 100 T
Tie bar spacing (H) 400 mm
Robot interface 1000-400
Screw diameter 40 mm
Tie bar spacing (V) 400 mm
Mould size

Clamping force 1200 T
Tie bar spacing (H) 1200 mm
Opening of the press 1500 mm
Screw diameter 133 mm
Tie bar spacing (V) 1200 mm

Clamping force 280 T
Tie bar spacing (H) 610 mm
Shot volume 748 cm³
Screw diameter 63 mm
Tie bar spacing (V) 610 mm
Platen length 910 mm

Clamping force 500 T
Tie bar spacing (H) 815 mm
Shot volume 1154 cm³
Screw diameter 70 mm
Tie bar spacing (V) 815 mm
Shot weight 1050 g

Clamping force 660 T
Tie bar spacing (H) 900 mm
Shot volume 4255 cm³
Screw diameter 115 mm
Tie bar spacing (V) 900 mm
Pressure on material 1480 bar

Clamping force 75 T
Tie bar spacing (H) 320 mm
Shot volume 115 cm³
Screw diameter 35 mm
Tie bar spacing (V) 320 mm
Shot weight 120 g

Clamping force 35 T
Tie bar spacing (H) 270 mm
Shot volume 24 cm³
Screw diameter 18 mm
Tie bar spacing (V) 270 mm
Shot weight 19 g

Clamping force 35 T
Tie bar spacing (H) 220 mm
Shot volume 49 cm³
Screw diameter 25 mm
Tie bar spacing (V) 220 mm
Pressure on material 1860 bar

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale

Introduction to injection moulding machines

The injection moulding machine also called an injection molding process or injection molder, belongs to the plastic machines category. The machine produces parts by injecting of plastic into a mould. Overall, the molding process is simple. There are 4 steps for the creation of a plastic part :
  1. The plasticization process
  2. The injection process
  3. The cooling process
  4. The ejection process

The raw material (plastic in this case) is softened under high pressure and then injected into the mould. Finally, the plastic is cooled into its final form.The molds installed on the machine usually consist of two shells (fixed part and movable part) which are pressed strongly against each other during molding then separated to allow ejection of the molded part. The injection plastic process can produce almost all kinds of plastic products  (flexible, rigid, polished, textured, colored or not, small, big….). The user has to take into account the variable size of the machine. (from a desk side to a room size).

Injection moulding machine requires  specific knowledge and training to be used. It’s required to have a good understanding of the molding process and of the machine characteristics.

What are the main advantages of using an injection moulding machine?

The injection moulding machine has many strengths such as repeatability, a wide range of plastic selection, low labor cost, low scrap losses and a quite high tolerance. However,  user may also face some problems when using this machine :For example, a temperature or internal pressure that is too high, under or over dosing in raw material and size problems...

With Exapro you can filter searches for your injection moulding machine  according to the following criteria :

  • Power in tons in T
  • Dist. X between tie bars in mm
  • Dist. Y between tie bars in mm
  • Screw diameter in mm
  • Shot volume in cm³
  • Shot weight in g

You can also display your searches by location of the machines, year of the machine and the machine manufacturer.

Area of use :

There is not a specific area of use for the injection machine. Generally, It’s used in plastic product manufacturing. Due to the rather high difficulty of using the machine, it’s more often used by professionals who work directly in plastic production.

Related subcategories :

Robots for plastic Injection

Injection moulding machines (all electric)

Injection moulding machines manufacturers 

Exapro regroups some of the most important manufacturers in injection moulding machines such as Battenfeld moulding machines , Arburg moulding machines and Sandretto moulding machines and Cincinnati milacron machinery.

Due to the high quality and precision of the machine, plastic injection molders can be quite expensive. With Exapro, you can find used injection moulding machine for sale at an affordable price. You can also sell your used machinery with Exapro. Please contact an Exapro agent if you have further questions about our marketplace.

As an example, here is the Krauss Maffei 250 - 1400 C1 injection moulding machines.

Find out now your used injection moulding machine for sale