M.V.D B06-3000 hydraulic shear Verified seller

Manufacturer M.V.D
Model B06-3000
Year
Location France FR
Category Shears - hydraulic guillotines
Product id P01211033

€31,000

Contact the seller

You have the same machine to sell?

Add it to our catalogue for FREE

Start selling

About this seller Verified seller

Client type Reseller
Active since 2019
Offers online 42
Last activity March 24, 2021

Specifications

Cutting length 3000 mm
Max. thickness 6 mm
Sheet support Yes
-------------------
Worked hours
Hours under power
State good
At local norms ---------
Status

Description

Hydraulic guillotine shear 3000x6 mm.
Swing-beam shears: the upper deck, pushed by 2 jacks, oscillates along an axis parallel to the lower blade.
The frame and the upper apron (closed box type) provide excellent rigidity and therefore constant play over the entire length of the cut.
The upper apron is made integral with the frame by means of pivots mounted on bearings, widely dimensioned and located on the neutral fiber of the flanges.
The low rake angle makes it possible to shear thin sheet edges with minimal tools.
The clearance between the blades is easily and precisely obtained by acting on a lever placed on the side of the shears.
Motorized rear gauge with visualization of dimensions on meter
ELGO P40T has a stroke of 1000 mm and is integral with the oscillating upper apron
The hydraulic sheet metal clamps are independent and close together at the ends for cutting narrow strips. The precision and quality of cut also depend on the efficiency of the sheet clamps which provide a variable clamping force in relation to the thickness and nature of the sheet to be sheared.
The control is carried out by a mobile pedal. The pressure on the pedal ensures the clamping of the sheet clamps then the descent of the slide. When you release the pedal, the slide goes up automatically. Thus, the cutting rate increases proportionally with the decrease in the cutting width.
HOERBIGER or REXROTH brand hydraulic equipment (protected by overload valves) is placed in the lower part and at the front of the machine. It is easily accessible, which facilitates routine maintenance operations.
The ELGO P40-T programmer can be used in:
TFT display with touchscreen operation The P40T integrates 3 operating modes:
Manual: Movement of the axes by pressing and holding the keys on the touch screen.
Simple: Simple movement to a requested position.
Program: Movement of the axes to a series of programmed positions.
The rest of the movements is carried out sequentially. In this case, the program consists of a series of simple movements. Digital outputs up to 2A
Analogue and pressure outputs depending on the material to be cut
Automatic cutting
Management of the plate stops
Sheet metal return management

Calculation of blade spacing, cutting angle
Rear protection
Access to the rear of the shears provided by 2 photoelectric cells controlled by a “Telemecanique” type Préventa safety module. When the operator goes to look for a sheet, he is obliged to reset the control, which forces him to look if no one is under the stop.
The rear part of the machine, completely free, allows the installation of equipment such as inclined planes, sheet supports, evacuators ...
- Electrical equipment 380 Volts - 50 Hertz - 3 Ph + Earth + Neutral.
- Steel blades with high wear resistance: 2 cutting edges for the upper blade and 4 edges
cutting for the lower blade.
- Remote control pedal.
- Emergency stop buttons.
- 2 front support arms.
- 1 Square ruler of 1 meter, with graduated ruler and retractable stop.
- 1000 mm rear stop on ball screw.
- Time meter.
- Table equipped with balls for sliding the sheets.
- Front protection allowing perfect visibility of the cutting line.
- Lighting of the cutting line.
- Stroke limiter, to increase the cutting rate when shearing narrow strips.
- Instruction manual with CE certificate of conformity.
- Full of oil done

Goniometer - Protractor cutting angle 0-180 °
Front retractable grille with contactor
Gooseneck 500 mm
Added value for plastic end caps Included s / B06-3000
Plastic end caps
Set of special blades for INOX on request
Sheet metal support extension bracket 1.5 - 2 - 3 meters 250.00 / 400.00 / 700.00
Rear pneumatic sheet support 3 meters 3.000,00
Adjustment of the clearance between motorized blade 2,200.00
CNC DELEM DAC 360 or CYBELEC DNC 61G
2 axes for clearance between blade + rear stop control 3.500.00

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. Exapro recommends to check the details with the seller before a purchase

How does Exapro work?

Using Exapro is super easy, here is how it works

Here is a selection of similar machines

Contact the seller