The GLEASON 726 REVACYCLE straight-tooth milling machine built in the United States, produces the teeth of the bevel gears at a speed of 49.7 m / min, used in differentials. The radial heads of the machine mill the detail with the relative movement of the wheel in relation to the cutter head during roughing. The reliable GLEASON 726 REVACYCLE milling machine for bevel gears guarantees the most accurate and precise machining of details. The total weight of the GLEASON NO 726 is approximately 9,000 kg.

Characteristics of the GLEASON 726 REVACYCLE milling machine for bevel gears

- minimum foot angle: 15 °
- maximum foot angle: 55 °
- maximum tooth height: 14.8 mm
- maximum width of the toothed rim measured at the foot line: 28 mm
- division range: 8-50 mm
- cone depth: 15.8 mm
- cone taper per foot: 15.4 mm
- bore with a cone: 57.2 x 77.9 mm
- diameter of the tapered bore at the large end: 99 mm
- hole diameter along the spindle: 22.3 mm
- knife head speed range: 32.6-49.7 m / min
- feeds (seconds per tooth): 2-3.1
- main drive motor power: 10 HP
- main drive engine revolutions (60 Hz / 50 Hz): 1800/1500 rpm
- hydraulic system motor revolutions (60 Hz / 50 Hz): 1800/1500 rpm
- coolant pump speed (60 Hz / 50 Hz): 3600/3000 rpm
- rotation of the chip removal motor (60 Hz / 50 Hz): 1800/1500 rpm
- floor space requirement (L x W): 320 x 221 cm
- the total weight of the machine 726 REVACYCLE: approx. 9 t

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. Exapro recommends to check the details with the seller before a purchase

Type Horizontal
Max spindle speed 1800 rpm
Max gear width 28 mm
Motor power 7.45712 kW
-------------------
Weight 9000 kg
Worked hours
Hours under power
State good
At local norms ---------
Status
Client type Reseller
Active since 2010
Offers online 377
Last activity March 29, 2024

Description

The GLEASON 726 REVACYCLE straight-tooth milling machine built in the United States, produces the teeth of the bevel gears at a speed of 49.7 m / min, used in differentials. The radial heads of the machine mill the detail with the relative movement of the wheel in relation to the cutter head during roughing. The reliable GLEASON 726 REVACYCLE milling machine for bevel gears guarantees the most accurate and precise machining of details. The total weight of the GLEASON NO 726 is approximately 9,000 kg.

Characteristics of the GLEASON 726 REVACYCLE milling machine for bevel gears

- minimum foot angle: 15 °
- maximum foot angle: 55 °
- maximum tooth height: 14.8 mm
- maximum width of the toothed rim measured at the foot line: 28 mm
- division range: 8-50 mm
- cone depth: 15.8 mm
- cone taper per foot: 15.4 mm
- bore with a cone: 57.2 x 77.9 mm
- diameter of the tapered bore at the large end: 99 mm
- hole diameter along the spindle: 22.3 mm
- knife head speed range: 32.6-49.7 m / min
- feeds (seconds per tooth): 2-3.1
- main drive motor power: 10 HP
- main drive engine revolutions (60 Hz / 50 Hz): 1800/1500 rpm
- hydraulic system motor revolutions (60 Hz / 50 Hz): 1800/1500 rpm
- coolant pump speed (60 Hz / 50 Hz): 3600/3000 rpm
- rotation of the chip removal motor (60 Hz / 50 Hz): 1800/1500 rpm
- floor space requirement (L x W): 320 x 221 cm
- the total weight of the machine 726 REVACYCLE: approx. 9 t

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. Exapro recommends to check the details with the seller before a purchase


Specifications

Type Horizontal
Max spindle speed 1800 rpm
Max gear width 28 mm
Motor power 7.45712 kW
-------------------
Weight 9000 kg
Worked hours
Hours under power
State good
At local norms ---------
Status

About this seller

Client type Reseller
Active since 2010
Offers online 377
Last activity March 29, 2024

Here is a selection of similar machines

Gleason 726 Revacycle Vertical gear hobbing machine