Sorry, this offer is no longer available on Exapro

Used Homag KAL 310/7/A20/S2 edgebander

Here is a selection of similar machines

single sided edge banding machine
Brand: Homag
Type: KAL310/7/A20/S2
Year: 2004

Equipment
- Motoric height adjustable top pressure with joined v-belt
- HOMATIC-control with enter unit NC2
- Hot melt gluing unit A20 for coil ware up to 3 mm and strip ware bis 20 mm
- Noise protection unit part
- End trimming unit chamfer/straight
- Empty space for further units

Technical data:
- Feed stepless adjustable 18-24 m/min
- Working height 950 mm
- Working width minimal: 55 mm at workpiece thickness 22 mm, 100 mm at workpiece thickness 60 mm (depending on the workpiece length)
- Workpiece overhang 30 mm
- Workpiece thickness 12 - 60 mm

- Edge material strips max. 0,4 - 20 mm
- Edge cross sectional area strips max. 900 mm2
- Edge material coil 0,3 - 3 mm
- Edge cross sectional area max.: at PVC 135 mm², at veneer 100 mm²
- Coil Ø max. 830 mm
- Pneumatic supplz 7-8 bar

Pre-milling unit
- 2 Motors each 3 kW

Workpiece pre-heating

Gluing unit A20
- Glue tank 5L
- Electronic temperature control with LED-display

- Magazine for massive edges, strip ware and coil ware

- Coil separation device

Pressure zone, autom. adjustable
- 1 driven pre-pressure rollers Ø. 150 mm
- 6 Post-pressure rollers Ø. 70 mm

End trimming unit chamfer/straight
for workpieces with covering layer overhang up to max. 10 mm
- 2 Motors each 0,5 kW, 200 Hz., 12000 1/min.
- For trimming the edge overhangs on frontal and rear edge

Rough milling unit 1,5 KW OPTIMAT
2 Motors on eabove the other
Each 1,5 kW, 200 Hz., 12000 1/min.

Form milling units FK11 manual
To process the edge overhangs on the upper and lower workpiece edge as well to mill around the frontal and rear workpiece edge in connection with end trimming and rough milling unit.
- 2 Motors each 0,55 kW, 200 Hz., 12000 1/min.
- Holder with quick change device

- Workpiece length single sided min. 240 mm, double sided 120 mm
- Distance between workpieces min. 680 mm
- Workpiece thickness 12 - 60 mm
- at workpiece thickness over 40 mm the min. workpiece length increases to min. 230 mm
- Edge thickness max. 5 mm

Mulit-post cleaning device MN21 automatical

Post cleaning device glued joint

Buffing unit top and bottom to make the edges handy
2 motors each 0,25 kW

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. Exapro recommends to check the details with the seller before a purchase

Board thickness 60 mm
Edge thickness 5 mm
Feed advance 24 m/min
Sound-proof cabin Yes
Glue tank Yes
-------------------
Worked hours
Hours under power
State good
At local norms ---------
Status visible
Datasheet Homag KAL 310/7/A20/S2
Client type Reseller
Active since 2013
Offers online 33
Last activity March 28, 2024

Description

single sided edge banding machine
Brand: Homag
Type: KAL310/7/A20/S2
Year: 2004

Equipment
- Motoric height adjustable top pressure with joined v-belt
- HOMATIC-control with enter unit NC2
- Hot melt gluing unit A20 for coil ware up to 3 mm and strip ware bis 20 mm
- Noise protection unit part
- End trimming unit chamfer/straight
- Empty space for further units

Technical data:
- Feed stepless adjustable 18-24 m/min
- Working height 950 mm
- Working width minimal: 55 mm at workpiece thickness 22 mm, 100 mm at workpiece thickness 60 mm (depending on the workpiece length)
- Workpiece overhang 30 mm
- Workpiece thickness 12 - 60 mm

- Edge material strips max. 0,4 - 20 mm
- Edge cross sectional area strips max. 900 mm2
- Edge material coil 0,3 - 3 mm
- Edge cross sectional area max.: at PVC 135 mm², at veneer 100 mm²
- Coil Ø max. 830 mm
- Pneumatic supplz 7-8 bar

Pre-milling unit
- 2 Motors each 3 kW

Workpiece pre-heating

Gluing unit A20
- Glue tank 5L
- Electronic temperature control with LED-display

- Magazine for massive edges, strip ware and coil ware

- Coil separation device

Pressure zone, autom. adjustable
- 1 driven pre-pressure rollers Ø. 150 mm
- 6 Post-pressure rollers Ø. 70 mm

End trimming unit chamfer/straight
for workpieces with covering layer overhang up to max. 10 mm
- 2 Motors each 0,5 kW, 200 Hz., 12000 1/min.
- For trimming the edge overhangs on frontal and rear edge

Rough milling unit 1,5 KW OPTIMAT
2 Motors on eabove the other
Each 1,5 kW, 200 Hz., 12000 1/min.

Form milling units FK11 manual
To process the edge overhangs on the upper and lower workpiece edge as well to mill around the frontal and rear workpiece edge in connection with end trimming and rough milling unit.
- 2 Motors each 0,55 kW, 200 Hz., 12000 1/min.
- Holder with quick change device

- Workpiece length single sided min. 240 mm, double sided 120 mm
- Distance between workpieces min. 680 mm
- Workpiece thickness 12 - 60 mm
- at workpiece thickness over 40 mm the min. workpiece length increases to min. 230 mm
- Edge thickness max. 5 mm

Mulit-post cleaning device MN21 automatical

Post cleaning device glued joint

Buffing unit top and bottom to make the edges handy
2 motors each 0,25 kW

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. Exapro recommends to check the details with the seller before a purchase


Specifications

Board thickness 60 mm
Edge thickness 5 mm
Feed advance 24 m/min
Sound-proof cabin Yes
Glue tank Yes
-------------------
Worked hours
Hours under power
State good
At local norms ---------
Status visible

About this seller

Client type Reseller
Active since 2013
Offers online 33
Last activity March 28, 2024