DOZAMET OWT 400A cleaner made in Poland in 1988. The cleaner is offered with a filter chamber. A few years ago the machine was thoroughly refurbished.

Technical specifications:
- useful capacity of the working chamber: 0.35 m3
- minimal dimensions of castings: min. 25 x 25 x 25 mm
- maximum dimensions of castings: 400 x 400 x 400 mm
- minimum wall thickness: 5 mm
- minimum unit weight of cleaned castings: 40 kg
- maximum casting load weight: 400 kg
- cleaning time for one load of iron castings: 3-6 min.
- cleaning time for one load of steel castings: 8-12 min.
- the amount of shot for the first loading: 700 kg
- recommended shot granulation: 0.5-2.5 mm
- number of casting rotors: 1 pc
- projection rotor efficiency: 150 kg / min. steel or iron shot
- total machine weight: 7500 kg
- the required efficiency of the dedusting device: 1.66 m3 / sec.
- negative pressure required at the connector: 500 Pa
- compressed air demand per change: 0.01 m3
- working pressure: 0.4-0.6 MPa
- total installed power: 14.7 kW
- machine dimensions (width x length x height): 3692 x 2249 x 5158 mm
- dimensions of the filter chamber (width x length x height): 1000 x 2100 x 3100 mm

Machine characteristics:
The cleaner is intended for cleaning iron and steel castings. The cleaning process takes place in a closed working chamber, in which perforated rubber tape is spread on the drums, by means of shot thrown by the blades of the projecting rotor and as a result of mutual rubbing of castings.

The cleaner consists of the following components:
- working chamber
- auger with sieve and drive
- suction hoses
- propeller thrower
- electrical equipment
- running the belt together with an auxiliary device
- tape drive
- chamber closure
- separator
- elevator

The running of the belt together with the auxiliary device is a set of three drums driving, tensioning and driving the belt without end. The guide wheels with protective shields located on the sides form a trough from rubber band. The belt drive positioned on the roof of the working chamber consists of an electric motor, a V-belt transmission, a reducer and a chain transmission. The back of the working chamber is closed with a double door facilitating the operation of the cleaner.

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. Exapro recommends to check the details with the seller before a purchase

-------------------
Length x width x height 3692.0 × 2249.0 × 5158.0
Weight 7500 kg
Worked hours
Hours under power
State good
At local norms ---------
Status
Client type Reseller
Active since 2010
Offers online 410
Last activity May 27, 2024

Description

DOZAMET OWT 400A cleaner made in Poland in 1988. The cleaner is offered with a filter chamber. A few years ago the machine was thoroughly refurbished.

Technical specifications:
- useful capacity of the working chamber: 0.35 m3
- minimal dimensions of castings: min. 25 x 25 x 25 mm
- maximum dimensions of castings: 400 x 400 x 400 mm
- minimum wall thickness: 5 mm
- minimum unit weight of cleaned castings: 40 kg
- maximum casting load weight: 400 kg
- cleaning time for one load of iron castings: 3-6 min.
- cleaning time for one load of steel castings: 8-12 min.
- the amount of shot for the first loading: 700 kg
- recommended shot granulation: 0.5-2.5 mm
- number of casting rotors: 1 pc
- projection rotor efficiency: 150 kg / min. steel or iron shot
- total machine weight: 7500 kg
- the required efficiency of the dedusting device: 1.66 m3 / sec.
- negative pressure required at the connector: 500 Pa
- compressed air demand per change: 0.01 m3
- working pressure: 0.4-0.6 MPa
- total installed power: 14.7 kW
- machine dimensions (width x length x height): 3692 x 2249 x 5158 mm
- dimensions of the filter chamber (width x length x height): 1000 x 2100 x 3100 mm

Machine characteristics:
The cleaner is intended for cleaning iron and steel castings. The cleaning process takes place in a closed working chamber, in which perforated rubber tape is spread on the drums, by means of shot thrown by the blades of the projecting rotor and as a result of mutual rubbing of castings.

The cleaner consists of the following components:
- working chamber
- auger with sieve and drive
- suction hoses
- propeller thrower
- electrical equipment
- running the belt together with an auxiliary device
- tape drive
- chamber closure
- separator
- elevator

The running of the belt together with the auxiliary device is a set of three drums driving, tensioning and driving the belt without end. The guide wheels with protective shields located on the sides form a trough from rubber band. The belt drive positioned on the roof of the working chamber consists of an electric motor, a V-belt transmission, a reducer and a chain transmission. The back of the working chamber is closed with a double door facilitating the operation of the cleaner.

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. Exapro recommends to check the details with the seller before a purchase


Specifications

-------------------
Length x width x height 3692.0 × 2249.0 × 5158.0
Weight 7500 kg
Worked hours
Hours under power
State good
At local norms ---------
Status

About this seller

Client type Reseller
Active since 2010
Offers online 410
Last activity May 27, 2024

Here is a selection of similar machines

Dozamet OWT 400 A