| Manufacturer | - |
|---|---|
| Model | - |
| Year | |
| Location | Spain
|
Overview
CNC plasma and oxy-fuel cutting table with a 12,000 × 2,500 mm effective cutting area, Lynx CNC controller and ESAB ESP-100i plasma power source. The system is configured for combined plasma and oxy-fuel cutting and was in daily production until it was dismantled. The equipment is currently disassembled and will require reassembly and commissioning at the buyer’s premises.
Key specifications (from seller information and known fields)
- Effective cutting area: 12,000 × 2,500 mm
- Process: CNC plasma and oxy-fuel cutting
- Plasma power source: ESAB ESP-100i
- Maximum output power: 12 kW
- Output-current range: 10–100 A
- Rated output: 100 A at 120 V DC
- Duty cycle: 100%
- Open-circuit voltage: 325 V DC
- Power factor at 12 kW: 0.96
- Efficiency at 12 kW: ~93%
- Electrical supply: three-phase, 50/60 Hz (compatible input voltages 200–575 V depending on configuration)
- Required compressed-air pressure: 6–10 bar; required airflow: 256 l/min at 6 bar
- Stated plasma capacities: stainless steel up to 20 mm, carbon steel up to 30 mm
- Oxy-fuel cutting capacity (seller information): over 70 mm
- Known fields: CNC: Yes; Max steel thickness: 30 mm; Nbr of heads: 2; Power: 12,000 W; Type of source: Plasma
Included equipment and visible components (supported by listing and photographs)
- 12,000 × 2,500 mm slatted cutting table with bed fingers/slat supports
- Travelling gantry with crossbeam
- Dual cutting torches/heads mounted on a vertical carriage
- Lynx CNC operator control panel (display, keypad, pushbuttons, rotary gauges and emergency-stop button)
- ESAB power/auxiliary units (yellow ESAB unit and an additional unit visible), with associated cables and hoses
- Multiple hoses and cables routed to the carriage and torches; sheet metal plates shown on the bed
Condition and notes (observed and reported)
- Table slats and sheet plates show surface rust and discoloration consistent with prior cutting use
- Torch tips and surrounding areas show soot/discoloration consistent with earlier cutting operations
- Hoses, cables and control-panel exterior show dirt, abrasion and signs of heavy use
- One photograph shows a torch in active cutting with a visible arc/flame and a bright cut line on the plate; this indicates live cutting activity in that image
Additional information
- The system was removed from production as part of an equipment renewal programme and is offered disassembled. Commissioning, installation and operator training may be negotiable with the seller. Buyers should allow for reassembly, electrical and compressed-air connections, and on-site commissioning.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
CNC Plasma and Oxy-Fuel Cutting Table 12,000 × 2,500 mm with ESAB ESP-100i
Description
Complete CNC plasma and oxy-fuel cutting system designed for large-format sheet-metal processing.
The installation comes from a company specialising in heavy and medium-heavy fabrication and was in daily production until it was dismantled as part of an equipment-renewal programme. It was fully operational before dismantling and is offered inspected and ready for reuse after reassembly.
The system includes a 12-metre cutting table, travelling gantry, plasma and oxy-fuel cutting heads, Lynx CNC controller and ESAB ESP-100i plasma power source.
The ESAB unit is a self-contained air-plasma system requiring only a suitable electrical connection and a clean, dry compressed-air supply. Commissioning, installation and operator training can potentially be negotiated.
Technical specifications
Process: CNC plasma and oxy-fuel cutting
Effective cutting area: 12,000 × 2,500 mm
CNC controller: Lynx
Plasma power source: ESAB ESP-100i
Output-current range: 10-100 A
Rated output: 100 A at 120 V DC
Duty cycle: 100%
Open-circuit voltage: 325 V DC
Maximum output power: 12 kW
Power factor at 12 kW: 0.96
Efficiency at 12 kW: approximately 93%
Electrical supply: three-phase, 50/60 Hz
Compatible input voltages: 200-575 V, depending on configuration
Required compressed-air pressure: 6-10 bar
Required airflow: 256 l/min at 6 bar
Plasma capacity in stainless steel: up to 20 mm
Plasma capacity in carbon steel: up to 30 mm
Oxy-fuel cutting capacity: over 70 mm
ESAB power-source dimensions: 838 × 546 × 693 mm
ESAB power-source weight: 185 kg
Included equipment
12,000 × 2,500 mm cutting table
Travelling cutting gantry
Lynx CNC control system
ESAB ESP-100i plasma power source
Plasma cutting head
Oxy-fuel cutting head
Associated cables, hoses and equipment shown in the photographs
Condition
The machine was operational before dismantling. It is currently disassembled and will require reassembly and commissioning at the buyer’s premises.
Please note that this description may have been translated or optimized with artificial intelligence (AI) automatically. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase.
| Client type | Machinery dealer |
| Active since | 2026 |
| Offers online | 1 |
| Last activity | Sept. 17, 2026 |
CNC Plasma and Oxy-Fuel Cutting Table 12,000 × 2,500 mm with ESAB ESP-100i
Description
Complete CNC plasma and oxy-fuel cutting system designed for large-format sheet-metal processing.
The installation comes from a company specialising in heavy and medium-heavy fabrication and was in daily production until it was dismantled as part of an equipment-renewal programme. It was fully operational before dismantling and is offered inspected and ready for reuse after reassembly.
The system includes a 12-metre cutting table, travelling gantry, plasma and oxy-fuel cutting heads, Lynx CNC controller and ESAB ESP-100i plasma power source.
The ESAB unit is a self-contained air-plasma system requiring only a suitable electrical connection and a clean, dry compressed-air supply. Commissioning, installation and operator training can potentially be negotiated.
Technical specifications
Process: CNC plasma and oxy-fuel cutting
Effective cutting area: 12,000 × 2,500 mm
CNC controller: Lynx
Plasma power source: ESAB ESP-100i
Output-current range: 10-100 A
Rated output: 100 A at 120 V DC
Duty cycle: 100%
Open-circuit voltage: 325 V DC
Maximum output power: 12 kW
Power factor at 12 kW: 0.96
Efficiency at 12 kW: approximately 93%
Electrical supply: three-phase, 50/60 Hz
Compatible input voltages: 200-575 V, depending on configuration
Required compressed-air pressure: 6-10 bar
Required airflow: 256 l/min at 6 bar
Plasma capacity in stainless steel: up to 20 mm
Plasma capacity in carbon steel: up to 30 mm
Oxy-fuel cutting capacity: over 70 mm
ESAB power-source dimensions: 838 × 546 × 693 mm
ESAB power-source weight: 185 kg
Included equipment
12,000 × 2,500 mm cutting table
Travelling cutting gantry
Lynx CNC control system
ESAB ESP-100i plasma power source
Plasma cutting head
Oxy-fuel cutting head
Associated cables, hoses and equipment shown in the photographs
Condition
The machine was operational before dismantling. It is currently disassembled and will require reassembly and commissioning at the buyer’s premises.
Please note that this description may have been translated or optimized with artificial intelligence (AI) automatically. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase.
Overview
CNC plasma and oxy-fuel cutting table with a 12,000 × 2,500 mm effective cutting area, Lynx CNC controller and ESAB ESP-100i plasma power source. The system is configured for combined plasma and oxy-fuel cutting and was in daily production until it was dismantled. The equipment is currently disassembled and will require reassembly and commissioning at the buyer’s premises.
Key specifications (from seller information and known fields)
- Effective cutting area: 12,000 × 2,500 mm
- Process: CNC plasma and oxy-fuel cutting
- Plasma power source: ESAB ESP-100i
- Maximum output power: 12 kW
- Output-current range: 10–100 A
- Rated output: 100 A at 120 V DC
- Duty cycle: 100%
- Open-circuit voltage: 325 V DC
- Power factor at 12 kW: 0.96
- Efficiency at 12 kW: ~93%
- Electrical supply: three-phase, 50/60 Hz (compatible input voltages 200–575 V depending on configuration)
- Required compressed-air pressure: 6–10 bar; required airflow: 256 l/min at 6 bar
- Stated plasma capacities: stainless steel up to 20 mm, carbon steel up to 30 mm
- Oxy-fuel cutting capacity (seller information): over 70 mm
- Known fields: CNC: Yes; Max steel thickness: 30 mm; Nbr of heads: 2; Power: 12,000 W; Type of source: Plasma
Included equipment and visible components (supported by listing and photographs)
- 12,000 × 2,500 mm slatted cutting table with bed fingers/slat supports
- Travelling gantry with crossbeam
- Dual cutting torches/heads mounted on a vertical carriage
- Lynx CNC operator control panel (display, keypad, pushbuttons, rotary gauges and emergency-stop button)
- ESAB power/auxiliary units (yellow ESAB unit and an additional unit visible), with associated cables and hoses
- Multiple hoses and cables routed to the carriage and torches; sheet metal plates shown on the bed
Condition and notes (observed and reported)
- Table slats and sheet plates show surface rust and discoloration consistent with prior cutting use
- Torch tips and surrounding areas show soot/discoloration consistent with earlier cutting operations
- Hoses, cables and control-panel exterior show dirt, abrasion and signs of heavy use
- One photograph shows a torch in active cutting with a visible arc/flame and a bright cut line on the plate; this indicates live cutting activity in that image
Additional information
- The system was removed from production as part of an equipment renewal programme and is offered disassembled. Commissioning, installation and operator training may be negotiable with the seller. Buyers should allow for reassembly, electrical and compressed-air connections, and on-site commissioning.
The following description has been generated using artificial intelligence based on the product information available. It is provided for guidance only and may not reflect all specifications or conditions. Please contact us if you need precise or confirmed details.
| Client type | Machinery dealer |
| Active since | 2026 |
| Offers online | 1 |
| Last activity | Sept. 17, 2026 |
Маса за плазмено и кислородно-горивно рязане с ЦПУ, 12 000 × 2 500 мм, с ESAB ESP-100i
CNC stůl pro plazmové a autogenní řezání o rozměrech 12 000 × 2 500 mm s zařízením ESAB ESP-100i
CNC-plasma- og gas-skærebord 12.000 × 2.500 mm med ESAB ESP-100i
CNC-Plasma- und Autogenschneidetisch 12.000 × 2.500 mm mit ESAB ESP-100i
Πίνακας κοπής με πλάσμα και οξυγόνο CNC διαστάσεων 12.000 × 2.500 mm με ESAB ESP-100i
CNC Plasma and Oxy-Fuel Cutting Table 12,000 × 2,500 mm with ESAB ESP-100i
Mesa de corte por plasma y oxicorte CNC de 12 000 × 2 500 mm con ESAB ESP-100i
Table de découpe CNC au plasma et à l'oxycoupage 12 000 × 2 500 mm équipée d'un ESAB ESP-100i
CNC plazma i kisikovo-gorivo stol za rezanje 12.000 × 2.500 mm s ESAB ESP-100i
12 000 × 2 500 mm-es CNC plazma- és oxigén-fúvóka vágóasztal ESAB ESP-100i berendezéssel
Tavolo da taglio al plasma e ossitaglio CNC da 12.000 × 2.500 mm con ESAB ESP-100i
CNC plazminio ir deguonies-kuro pjovimo stalas 12 000 × 2 500 mm su „ESAB ESP-100i“
CNC-plasma- en autogeen-snijtafel 12.000 × 2.500 mm met ESAB ESP-100i
Stół do cięcia plazmowego i tlenowo-paliwowego CNC o wymiarach 12 000 × 2 500 mm z urządzeniem ESAB ESP-100i
Mesa de corte a plasma e oxicorte CNC de 12 000 × 2 500 mm com ESAB ESP-100i
Masă de tăiere CNC cu plasmă și oxigaz de 12.000 × 2.500 mm, echipată cu ESAB ESP-100i
Стенд для плазменной и газорезательной обработки с ЧПУ размером 12 000 × 2 500 мм с оборудованием ESAB ESP-100i
CNC plazma i oksi-gorivno rezanje, radna površina 12.000 × 2.500 mm sa ESAB ESP-100i
CNC-skärbord för plasma- och gasskärning, 12 000 × 2 500 mm, med ESAB ESP-100i
ESAB ESP-100i donanımlı 12.000 × 2.500 mm boyutlarında CNC Plazma ve Oksijen-Yakıt Kesim Masası
EN
- Languages
English (GB)