GENERAL FEATURES
- Upper presser height adjustable numerical control in automatic mode
- Control HOMATIC NC21, NC Machine FULL !!
DATA ELEMENT AND SKIRTS:
- Feed rate of 12-18 m / min
- Minimum width (depending on the length of an element)
55 mm the element 22 mm
100 mm the element 60 mm
- Working height 950 mm
- Projection element: 30 mm
- Applied to the edges of the material (bar) 0.4 - 20 mm
- The periphery of the roller: 0,3 - 3 mm
- Max. Roll diameter: 830 mm
PRE-MILLING UNIT:
- For pre-milling parts before wrapping
- 2 motors, each with a capacity of 3 kW, 150 Hz, 9000 rpm
- Both controlled electro-motors
- A device to inflate the elements
- Together with the tools:
- Two diamond cutter heads integrated with the ejector, D = 125 x 35 x 30 mm, KN, Z = 2x3
UNIT OKLEJAJĄCY:
The unit includes:
PRELIMINARY HEATING ELEMENT
- To heat the surface of the narrow before applying the adhesive
- Provides better quality bonding
UNIT FOR melt adhesive A34
- Electronic temperature control
- Automatic lowering of the temperature of glue during work breaks
WAREHOUSE IN ROLL EDGE
- Control edges of stopping feed
- Adjust the height of the warehouse of +/- 10 mm using a spindle
- The sequencing periphery of administration
PRESSURE ZONE C:
- 1 roll clamping diameter of 150 mm, the drive
- 6 rolls retaining a diameter of 70 mm
- Pneumatic adjustment of clamping force
- Central adjustment to different thicknesses of the rim
UNIT SHUT-OFF PHASE / STRAIGHT HL83
- Allowance for cutting off the periphery of the front and rear edge of the
- 2 motors, each with a power of 0.5 kW, 200 Hz, 12000 rpm
- Together with the tools 2 ball off HM with a diameter of 120 mm,
Automatic adjustment of pressure zones, electronic timer for the glue tank
REPLACEMENT UNIT glue PU34 OPTIMAT
- Teflon-coated
- Heated roll adhesive
- PU adhesive applicators, for example. In the granulate
- Thickness of edges up to 6 mm
- A set of melting HHS-PUR
- Temperature control
- Distribution roller to adjust the amount of
UNIT SHUT-OFF HL84 / 85 instead of HL 81/83
Controlled separately from the control panel for soft edges
Pneumatic adjustment phase / straight, pneumatic control unit engine shutoff
Milling unit UP / DOWN
- 2 motors 1 kW.
- Height adjustment of the upper clamp
- Edge thickness up to 20 mm
- Max thickness of 60 mm
- A set of tiltable 0-25 °
- Two cutters HM 70 x 25 mm, HSK25, Z = 4
Rounding unit FK11, MANUAL:
- Treatment projecting rim on the upper and lower edge of the milling, and the front and rear edge of the
- For each profile and the edge (of wood or plastic) you will need a separate removable head
- 2 motors 0,55 kW 200 Hz, 12000 rpm
- Feed max 20 m / min
- Working length min. 240 mm on one side
- Thickness of 12-60 mm
- Max edge thickness 5 mm
KIT HAND indexable REMOVABLE HEADS
- 2 interchangeable heads with manual adjustment for different thicknesses of the rim at the milling stage and / or manual set-up of the milling phase on the beam
- Max. Edge thickness for milling phase of the tool radius:
- 1.5 R = 0.6 2.0 mm R = 0.8 mm, R = 3.0 1.0 mm
Automatic multi-cyclin MN21
automatic set-up or at different radii from the radius of the lift-off phase and to the upper and lower tools on the side of the working area - for max. three different profiles
- 2 knives HM phase 20 degrees / R = 1.5 / R = 2 /
TEAM 2 BRUSH polishing UP / DOWN
The team consists of:
- Glue scraper for the removal of surplus glue from the point of connection between the lip and the plate
- Height adjustment
Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. Exapro recommends to check the details with the seller before a purchase