Sorry, this offer is no longer available on Exapro

BRANDT Ambition 1200 Edgebander

Here is a selection of similar machines

Year: 2009.
208-480v; 3ph; 60.
Feed speed of 11 meters/36 FPM. - Equipped with: Operator control panel at eye-level, automatic height adjustment with top pressure beam for all workstations; electronic line control (no limit switches), digital height indicator on holddown beam, electronic motor brakes on trimmers.

EC-10+ controller.

Automatic magazine for strip and coil feeding.

Panel pre-heater (direct contact style) for achieving optimal bonding quality.

Hot melt granulate glue application system with 12 minute heat up time and no lubrication needed.

Glue unit heating is turned off if no work piece is run within 9 minutes. Glue unit heating is also turned off 3 minutes after the safety cover is opened and control voltage is not re-activated.

0.4 - 3 mm (1/8") Edge thickness cap., 8 - 50 mm panel thickness, 60 mm min. panel width and 140 mm min. length.

Equipped with: Hot Melt granulate glue system with fast start-up (10 - 12 Min heat-up) (when idle drops to 150°it takes 2-1/2 Min to re-activate).

3 mm PVC Pneumatic guillotine for coil cutoff, automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine.

3-Roller pressure section (1st driven, 2 idle) w/electronically controlled & feed speed synchronized drive roll.

Workstations: Vertical travel double motor front & rear end trim with 0° - 15° horz. bevel cap. (0.25 HP - 12,000 RPM motors);

Top & bottom flush/bevel trimmers (0.35 HP - 12,000 RPM motors),

bevel 0° to 15°;

Last Station: Top & bottom buffing unit (0.15 HP - 2,750 RPM motors).

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. Exapro recommends to check the details with the seller before a purchase

Board thickness 50 mm
Edge thickness 8 mm
Feed advance 11 m/min
Glue tank Yes
-------------------
Worked hours
Hours under power
State like new
At local norms ---------
Status
Datasheet Brandt Ambition 1200
Client type Reseller
Active since 2012
Offers online 20
Last activity March 11, 2024

Description

Year: 2009.
208-480v; 3ph; 60.
Feed speed of 11 meters/36 FPM. - Equipped with: Operator control panel at eye-level, automatic height adjustment with top pressure beam for all workstations; electronic line control (no limit switches), digital height indicator on holddown beam, electronic motor brakes on trimmers.

EC-10+ controller.

Automatic magazine for strip and coil feeding.

Panel pre-heater (direct contact style) for achieving optimal bonding quality.

Hot melt granulate glue application system with 12 minute heat up time and no lubrication needed.

Glue unit heating is turned off if no work piece is run within 9 minutes. Glue unit heating is also turned off 3 minutes after the safety cover is opened and control voltage is not re-activated.

0.4 - 3 mm (1/8") Edge thickness cap., 8 - 50 mm panel thickness, 60 mm min. panel width and 140 mm min. length.

Equipped with: Hot Melt granulate glue system with fast start-up (10 - 12 Min heat-up) (when idle drops to 150°it takes 2-1/2 Min to re-activate).

3 mm PVC Pneumatic guillotine for coil cutoff, automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine.

3-Roller pressure section (1st driven, 2 idle) w/electronically controlled & feed speed synchronized drive roll.

Workstations: Vertical travel double motor front & rear end trim with 0° - 15° horz. bevel cap. (0.25 HP - 12,000 RPM motors);

Top & bottom flush/bevel trimmers (0.35 HP - 12,000 RPM motors),

bevel 0° to 15°;

Last Station: Top & bottom buffing unit (0.15 HP - 2,750 RPM motors).

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. Exapro recommends to check the details with the seller before a purchase


Specifications

Board thickness 50 mm
Edge thickness 8 mm
Feed advance 11 m/min
Glue tank Yes
-------------------
Worked hours
Hours under power
State like new
At local norms ---------
Status

About this seller

Client type Reseller
Active since 2012
Offers online 20
Last activity March 11, 2024